User Account

All Pages

If we were told that the water will reach a temperature of

Assignment Help Mechanical Engineering
Reference no: EM13624303

A tank has a stirrer that delivers 200 kJ of work on 100 kilograms of water at 45 degrees Celcus. Assume all of the work done by the stirrer is transferred to the water and the tank does not change temperature with the water. Find:

A.) the change of internal-energy of the water

B.) final temperature of the water

C.) If we were told that the water will reach a temperature of 46 degrees Celcius if the stirrer was 100% efficient in this situation, what is the actual efficiency of our stirrer?

Reference no: EM13624303

Questions Cloud

A dean of men wishes to estimate the average cost of the : a dean of men wishes to estimate the average cost of the freshman year at a particular college correct to within 260
A spherical shell of inner radius 20 cm and outer radius : a spherical shell of inner radius 2.0 cm and outer radius 6.0 cm is charged to 9 nc a point charge of -6 nc is placed
Suppose you wish to estimate the difference between the : suppose you wish to estimate the difference between the mean acidity for rainfalls at two different locations one in a
If we were told that the water will reach a temperature of : a tank has a stirrer that delivers 200 kj of work on 100 kilograms of water at 45 degrees celcus. assume all of the
If we were told that the water will reach a temperature of : a tank has a stirrer that delivers 200 kj of work on 100 kilograms of water at 45 degrees celcus. assume all of the
The potential on the outer surface of the membrane is 516 : the membrane that surrounds a certain type of living cell has a surface area of 7.1 x 10-9 m2 and a thickness of 1.6 x
Estimate the force of the roof at the opening pressures for : fluid mechanics for chemical engineers.nevers2-11large hydrocarbon storage tanks normally have a valve on their vents
The relationship between pressure and volume during the : oxygen o2 gas within a piston-cylinder assembly undergoes an expansion from a volume v1 0.01 m3 to a volume v2 0.03
An ice chest is constructed of 04 mm thick plain-carbon : an ice chest is constructed of 0.4 mm thick plain-carbon steel plate a 1.9 cm thick layer of styrofoam k0.033 wm c and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A 1875 inch diameter shaft machined from aisi 1018 cd

a 1.875 inch diameter shaft machined from aisi 1018 cd steel supports a bending load during operation at 1750 rpm. if

  The air surrounding the piston-cylinder is at 147 psi what

one cubic foot 1 ft3 of air is contained in a piston - cylinder arrangement. the axis of the cylinder is oriented in

  What load rating should be used to enter the timken company

a straight roller bearing is subjected to a radial load of 12 kn. the life is to be 4000 h at a speed of 750 revmin.

  Using a unifrom mesh size deltax deltay determine the

consider steady two dimensional heat transfer in a square cross section 3cm x 3cm with the prescribed temperatures at

  Determine the reduction in heat loss per unit length after

to reduce heat losses from a horizontal isothermal cylinder of radius ri 20 mm which is located in a large room in

  Asuming that the disk rolls without slip and the force p

assuming that the disk rolls without slip and the force p 18 n in the positive x-directionradius of disk r 20 cmmass

  Find the maximum shear stress and normal stress for the

a quartz sphere of 20mm diameter is pressed into a flat thick carbon steel plate with a force of 5 n. find the maximum

  5 lbm of air is compressed in a piston cylinder assembly

5 lbm of air is compressed in a piston cylinder assembly from 1 bar 300k to 5 bar according to a polytropic process

  A cylindrical steel pressure vessel with mean diameter

A cylindrical steel pressure vessel with mean diameter 1.5 m

  Design the pump power and the diameter of brunching pipes

Design the pump power and the diameter of brunching pipes D1, D2, D3, so that the flow rate coming into all buildings are Q1=Q2=Q3=4.5m^3/hr, when all four valves v, V1, V2, V3 are open.

  Calculate the quality if saturated or the temperature if

steam enters an insulated nozzle with a velocity of 500 ms and a pressure of 5.0mpa and a temperature of 600 degrees

  What is effect of increasing the cutting feed rate

What happens to the cutting and thrust force as tool rake angle and cutting speed are increased and what is the relation between the cutting and thrust forces to the depth of cut?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd