If we can achieve 10percent of the maximum theoretical work

Assignment Help Mechanical Engineering
Reference no: EM13610994

A flat plate solar collector is to be considered as a means to drive a pump to irrigate crops. This will be used in place of natural gas pumps presently in use for irrigation. Consider using a single plate collector system that can drive a perfect pump. The insolation is 317 Btu/hr-ft2.

a) Make a plot of the efficiency (work delivered to pump water/solar energy striking collector) as a function of the fraction of energy removed from the collector (collector efficiency).

b) If we can achieve 10percent of the maximum theoretical work, determine the size of the collector required to pump 1000 gpm from a well 1500 ft. The well water temperature is 60 F.

Reference no: EM13610994

Questions Cloud

Leslie blandings division manager of audiotech inc was : leslie blandings division manager of audiotech inc. was debating the merits of a new product - a weather radio that
At a time 936 seconds after it is released the particle has : a particle with charge -6.24 times 10-6 coulombs is released at rest in a region of constant uniform electric field.
Discuss relative costs amp benefits for firms to : discuss relative costs amp benefits for firms to mandatorilydisclose information about their operating segments
On september 1 a customers account balance of 2300 was : on september 1 a customers account balance of 2300 was deemed to be uncollectible. what entry should be recorded on
If we can achieve 10percent of the maximum theoretical work : a flat plate solar collector is to be considered as a means to drive a pump to irrigate crops. this will be used in
In an alcohol-in-glass thermometer the alcohol column has : in an alcohol-in-glass thermometer the alcohol column has length 11.84 cm at 0.0 degrees c and length 22.87cm at 100.0
Nami yee is a contractor specializing in custom-built : nami yee is a contractor specializing in custom-built jacuzzis. on my 1 2012 her ledger contains the following data.
Unlike the electric field the potential will be zero at : a doubly ionized carbon atom with charge 2e is located at the origin of the x axis and an electron with charge -e is
Edwards hometown forks washington is usually very cloudy : edward and his friends cannot go outside when it is sunny because they are vampires. edwards hometown forks washington

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Prepare the project objectives based on the requirement out

prepare the project objectives based on the requirement out lined at the next page.the following is the project

  What is the proeutectoid phase

Consider 6.0 kg of austenite containing 0.45 wt% C, cooled to below 727 degrees Celcius (1341 degrees Farenheit).

  10 c at the top and bottom surfaces respectively if the

the concrete slab of a basement is 11 m long 8 m wide and 0.20m thick. during the winter temperatures are nominally 17

  A rigid tank contains 20 lbm of air at 50 psia and 80o f

a rigid tank contains 20 lbm of air at 50 psia and 80o f. the air is now heated until its pressure doubles. determine

  Dtermine a the rate of shaft work transfer in kw b the

a rigid chamber contains 100 kg of water at 500 kpa 100 c. a paddle wheel stirs the water at 1000 rpm with a torque of

  An airplane moves forward at a speed w1 971 kph the frontal

an airplane moves forward at a speed w1 971 kph. the frontal intake area of the jet engine is a1 0.8 m2 and the

  Finding the volume of hydrogen

Finding the volume of hydrogen, A hydrogen filled balloon of the type used in cosmic ray studies is to be expanded to its full size which is a 100-ft diameter sphere, without stress in the wall at an altitude of 150,000 ft.

  Find the velocity of the final system

If the bullets stick to the block and they move together find the velocity of the final system and find the total impulse of each bullet if the movement takes 0.5s before coming to a stop.

  Isometric drawing make an isometric drawing of the v stop

make an isometric drawing of the v stop shown in figure 3. use a suitable scale to depict the ltbrgtview well on an a3

  Find the shaft id needed to obtain a maximum deflection

Find the shaft ID needed to obtain a maximum deflection at the center of 3 mm if the shaft OD is 22 cm. Assume the shaft to be the same length between supports as the length of the paper roll.

  What steel specification suitable for structural application

Find the stress in both members shown below and what steel specifications (types of steel) are suitable for structural applications?

  Sketch the schematic diagram of the circuit with the two

two resistors are given r1 470 ohms and r2 1200 ohms a the two resistors are connected in series with a 48 v source.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd