If upon initial null balance r3 is 1275 ohms and if when r2

Assignment Help Mechanical Engineering
Reference no: EM13603906

A simple wheatstone bridge as shown in fig. 7.10 is used to determine accurately the value of an unknown resistance R1 located in leg 1. If upon initial null balance R3 is 127.5 ohms and if, when R2 and R4 are interchanged, the null balance is achieved when R3 is 157.9 ohms, what is the value of the unknown resistance R1?

Reference no: EM13603906

Questions Cloud

Identify the type of sampling used random systematic : identify the type of sampling used random systematic convenience stratified or cluster. to estimate the percentage of
Deschambault inc is working on its cash budget for december : deschambault inc. is working on its cash budget for december. the budgeted beginning cash balance is 14000. budgeted
A single branch closed tube reads 35 cm connected to point : a u manometer reads 20 cm air as operating fluid and a given manometric fluid. a single branch closed tube reads 35 cm
Instead of rolling a die 100 times use statcrunch to : instead of rolling a die 100 times use statcrunch to simulate 100 rolls of a die. use statcrunch to create a random
If upon initial null balance r3 is 1275 ohms and if when r2 : a simple wheatstone bridge as shown in fig. 7.10 is used to determine accurately the value of an unknown resistance r1
Debbie acquired computer equipment for her business on june : debbie acquired computer equipment for her business on june 15 2009 for 32000. in 2009 debbie claimed a regular macrs
Two coupled boxcars are rolling along at 35 ms when they : two coupled boxcars are rolling along at 3.5 ms when they collide with and couple to a third stationary boxcar. a what
For 2010 omaha mechanical has a monthly overhead cost : for 2010 omaha mechanical has a monthly overhead cost formula of 42900 6 per direct labor hour. the firms 2010
Assuming the center-to-center distance of two atoms not : under a stress of 1105 mpa a sample of ag has a modulus of elasticity of 580 gpa. assuming the center-to-center

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The diffusion constant do and activation energy q of c in

the diffusion constant do and activation energy q of c in bcc fe is 0.01 cm2sec and 80kjmol respectively. in fcc fe the

  Determine the heat transfer rate in and out of the cycle

a heat pump cycle operates between a geothemial reservoir and your house. the cycle requires 200 kw to operate with a

  Why does a car engine stop

Why does a car engine stop when we turn the key even when the vehicle is running? The engine should run on alternator in case of a petrol engine and on it's own in case of a diesel engine. Then how does it stop exactly?

  Electronic components are mounted on the inner surface of a

electronic components are mounted on the inner surface of a horizontal cylindrical duct whose inner diameter is 0.2m.

  What tube diameter is required for the model

What tube diameter is required for the model if dynamic similarity is to be maintained between model and prototype?

  What is the k.e. of the satellite

A satellite has been placed in a circular, sun-synchronous orbit at an altitude of 1300.0 km. The satellite has a mass of 5,000.0 kg. What is the K.E. of the satellite?

  Discuss whether the following situations should be modeled

discuss whether the following situations should be modeled as closed systems or open systems. clearly define the

  A vehicle starts from rest then moves rectilinear with a

a vehicle starts from rest then moves rectilinear with a velocity of v 2t2 for 5 s until it reaches a velocity of 50

  Find the velocity of the bullet and block just after impact

Find the velocity of the bullet and block just after impact.

  Determine the velocity of the collars a and b

the motion of the slender 10kg rod AB is guided by collars of negligible mass that slide freely on the vertical and horizontal rods. knowing that the bar is released from rest when θ=30, determine the velocity of the collars A and B when θ = 60.

  Asignment overview carbon fibre reinforced polymers cfrp

assignment overview carbon fibre reinforced polymers cfrp have been used extensively in aerospace applications due to

  Hot water is pumped through a plate heat exchanger the hot

hot water is pumped through a plate heat exchanger. the hot water side of the heat exchanger consists of 16 plates of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd