If this bullet was fired into 1 lbm of water at room

Assignment Help Mechanical Engineering
Reference no: EM13644413

A 9 mm bullet with mass 0.28 oz = 0.0175 lbm exits a pistol at 1250 ft/s/ Find the kinetic energy in Btu. If this bullet was fired into 1 lbm of water at room temperature and all of the kinetic energy was converted into increasing the temperature of the water, find the water temperature increase in degrees F.

Reference no: EM13644413

Questions Cloud

For these conditions what is the force in units of lbf and : consider a subsonic engine inlet i.e. a diffuser with an inlet area of 2300 in2 and an exitinlet area ratio of 1.44.
Calculate the test statistic x3o to test the manufacturers : a manufacturer of precision measuring instruments claims that the standard deviation in the use of the instruments is
A spring has a spring constant k 14 875 nm if the spring is : a spring has a spring constant k 14 8.75 nm. if the spring is displaced 0.150 m from its equilibrium position what is
In a experiment you fill a 250 ml erlenmeyer flask with the : 1. in a experiment you fill a 250 ml erlenmeyer flask with the vapor. why must the volume of the flask be determined by
If this bullet was fired into 1 lbm of water at room : a 9 mm bullet with mass 0.28 oz 0.0175 lbm exits a pistol at 1250 fts find the kinetic energy in btu. if this bullet
A 50g ball travelling at 25 ms is bounced off a brick wall : a 50g ball travelling at 25 ms is bounced off a brick wall and rebounds at 22 ms. if the ball is in contact with the
A ball is launched into the air at an angle of 60deg above : a ball is launched into the air at an angle of 60deg above the horizontal with a speed of 21.0 ms. a what are the x-
Assume constant specific heat ideal gas properties : a mass of 0.25 kg of co2 at a temperature of 300 k and pressure of 100 kpa is heated at constant pressure to a volume
A ball is tossed from an upper-story window of a building : a ball is tossed from an upper-story window of a building. the ball is given an initial velocity of 8.30 ms at an angle

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The enthalpies of entering and exiting fluid are 27912 kjkg

a system receives 0.756 kgs of a fluid at a velocity of 36.58 ms at an elevation of 30.48 m. at the exit at an

  Find out the coefficients m and b of the function you

below is measured voltage v at different time stimes nbsp nbsp nbspnbsp 0nbspnbspnbspnbsp 0.5nbspnbsp 1nbspnbsp 1.5nbsp

  A supersonic aircraft consumes 5320 imperial gallons of

a supersonic aircraft consumes 5320 imperial gallons of kerosene per hour of flight and flies an average of 14 hours

  What speed vb will cause the car to lose contact with the

a formula-1 car encounters a hump which has a circular shape with smooth transitions at either end. a what speed vb

  Express this compressor work rate in kilowatts and

a heat pump with the elements shown in figure 7.25 condenser to valve to evaporator to compressor to condenser is to be

  Determine a the time at which the velocity will be zero b

the position of a particle which moves along a straight line is defined by the relation x t3 - 6t2 - 15t - 40 where x

  Determine the speed of the train

If the engine exerts a traction force of 1/8 of the weight of the train, determine the speed of the train when it has traveled up the slope a distance of 1.1 . Neglect rolling resistance.

  Determine the shear force v and bending moment m at a cross

a determine the shear force v and bending moment m at a cross section located 3.0m from the left-hand support.b find

  The body starts from the position sx0i with initial speed

the acceleration of a particle moving along a straight line is inversely proportional to its speed with the constant of

  Determine the required mass flow rate of air for a net

air is used as the working fluid in a simple ideal brayton cycle that has a pressure ratio of 10 a compressor inlet

  Estimate the force of the roof at the opening pressures for

fluid mechanics for chemical engineers.nevers2-11large hydrocarbon storage tanks normally have a valve on their vents

  Two points b and c lie on radial line of a rotating disk

two points b and c lie on radial line of a rotating disk. the points are 2 inches apart. vb700 ftmin and vc880ftmin.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd