If the shell-and-tube heat exchanger has a uas value of

Assignment Help Mechanical Engineering
Reference no: EM13641012

In a 1-shell and 2-tube heat exchanger, cold water with inlet temperature of 20 degree C is heated by hot water supplied at the inlet at 80 degree C. The cold and hot water flow rates are 5000 kg/h and 10,000 kg/h, respectively. If the shell-and-tube heat exchanger has a UAS value of 11,600 W/K, determine the cold water and hot water outlet temperatures. Assume Cpc = 4178 J/kg K and cph. = 4188 J/kg K.

Reference no: EM13641012

Questions Cloud

Some units can be calibrated by using a tuning fork holding : police radars determine speed by measuring the doppler shift of radio waves reflected by a moving vehicle. the do so by
Supposed 57 of the registered voters in a country are : supposed 57 of the registered voters in a country are republican.if a sample of 722 voters is selected what is the
Estimate the minimum collector area ft2 required for a : solar energy is used to warm a large collector plate. this energy in turn is transferred as heat to a fluid in a heat
At the end of this time the boat continues for an : a speedboat starts from rest and accelerates at 2.01 ms2 for 7.00 s. at the end of this time the boat continues for an
If the shell-and-tube heat exchanger has a uas value of : in a 1-shell and 2-tube heat exchanger cold water with inlet temperature of 20 degree c is heated by hot water supplied
You have a 25kd histidine tagged bacterial protein 100 : you have a 25kd histidine tagged bacterial protein 100 pure.you apply this pure protein to a ni2-agarose column. then
If the overall heat transfer coefficient is 880 wm2 k : cold water cp 4180 jkg k leading to a shower enters a thin-walled double-pipe counter-flow heat exchanger at 15 degree
A 1 farad capacitor is charged to 10 volts call this : a 1 farad capacitor is charged to 10 volts. call this capacitor a. it has a certain amount of stored charge. it is
In a sample of 108 toddlers the average height was found to : in a sample of 108 toddlers the average height was found to be 36.5 inches with a standard deviation of 1.1give a point

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Refrigerant-134a is being transported at 1kgs through a

refrigerant-134a is being transported at .1kgs through a teflon tube of inside diameter di 25mm and outside diameter

  A short squared timber post supports a load of 115000

a short squared timber post supports a load of 115000 pounds. if the allowable unit compressive stress is 1000 psi what

  Considering air inside the cylinder as the system calculate

consider a vertical piston-cylinder assembly with a 50 kg piston attached to a spring and exposed to atmospheric

  A missile with a conical nose cone with a semivertex angle

a missile with a conical nose cone with a semivertex angle of 16 deg is flying through sea level air at a speed of 817

  The diameter of one pipe is twice the diameter of the

two pipes are connected together in series. the diameter of one pipe is twice the diameter of the second pipe. with

  Observing plastic deformationthe aim of this demonstration

observing plastic deformationthe aim of this demonstration is to make some observations of the surface relief produced

  The 2-kg ball rests between the 45 degree grooves a and b

the 2-kg ball rests between the 45 degree grooves a and b of the 10 degree inlcine and against a vertical wall at c. if

  A motor car shaft consist of a steel tube 30 mm internal

a motor car shaft consist of a steel tube 30 mm internal diameter and 4 mm thick .thee engine develops 10kw at

  If the point of landing is 20 ft away determine the

during a race the dirt bike was observed to leap up off the small hill at a at an angle of 60o from the horizontal. if

  Calculate the concentration of molybdenum

Calculate the concentration (in weight percent) of molybdenum that must be added to tungsten to yield an alloy that contains 1.51 x 1022 Mo atoms per cubic centimeter.

  What are the corresponding values of tensile strength yield

a cylindrical steel rod 0.5 in diameter is cold worked to reduce the area. the new diameters in 3 cases are 0.43in

  If the turbine dissipates heat to its surroundings at the

a turbine operates at steady state with steam flowing through it at a rate of 36 kgmin. the steam enters the turbine at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd