If the scrubber removes 92 molar basis of the entering h2s

Assignment Help Mechanical Engineering
Reference no: EM13621341

A flue gas is which the mole fraction of H2S is 0.002 enters a scrubber operating at steady state at 200 deg F, 1 atm and a volumetric flow rate of 20,000 ft^3/h. if the scrubber removes 92% (molar basis) of the entering H2S, determine the rate at which H2S is removed in LB/h. Comment on why H2S should be removed from the gas stream.

Reference no: EM13621341

Questions Cloud

Arbitron media research inc conducted a study of the ipod : arbitron media research inc. conducted a study of the ipod listening habits of men and women. one facet of the study
Calculate the convective heat transfer loss to the air from : a square aluminum plate 5 mm thick and 200 mm on a side is heated while vertically suspended in quiescent air at 40c. a
What is the critical f value for a sample of 9 observations : what is the critical f value for a sample of 9 observations in the numerator and 6 in the denominator? use a two-tailed
What is your point estimate of the percentage of satisfied : virtual call centers are staffed by individuals working out of their homes. most home agents earn 10 to 15 per hour
If the scrubber removes 92 molar basis of the entering h2s : a flue gas is which the mole fraction of h2s is 0.002 enters a scrubber operating at steady state at 200 deg f 1 atm
Develop a 98 confidence interval for the proportion : during a national debate on changes to health care a cable news service performs an opinion poll of 470 small-business
Determine the horizontal acceleration a of the frame : the collar a is free to slide along the smooth shaft b mounted in the frame. the plane of the frame is vertical.
Explain why ms-within is not an appropriate error term : explain why ms-within is not an appropriate error term demoninator for the repeated measures
In a published study the author has presented a scatter : in a published study the author has presented a scatter plot of data with a line drawn through the data points. this

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Generate a script to draw the perpendicular bisector of

generate a script to draw the perpendicular bisector of any two points using ginput command. the length of the

  A pitot-static probe connected to a water manometer is used

a pitot-static probe connected to a water manometer is used to measure the velocity of air. if the de?ection

  Determine the speed of the block at the instant

If the truck starts from rest when xD is zero, and moves forward with a constant acceleration of aD = 5 m/s2, determine the speed of the block at the instant xD = 3 m.

  Problem a 5x5 plate with a crack size of 2a15 is under a

problem a 5x5 plate with a crack size of 2a1.5 is under a spectrum load as shown below. the plate has a yield strength

  What is the actual strain

You have a 120 Ω quarter bridge 2 wire set up with Sg=2.10 and an unknown lead wire resistance. A 59880Ω calibration resistor is switched in parallel to the gage only and a recording instrument is set to give a -100 mm deflection for this calibrat..

  Compare to the actual performance

Get information about a car engine .drive the ideal performance using the appropriate cycle and compare to the actual performance.

  If excess energy is carried away from the plant by a river

a nuclear power plant has an electrical power output of 1800 mw and operates with an efficiency of 30. if excess

  Find the magnitude of the average velocity

Remember that velocity is a vector quantity so find the magnitude of the average velocity and the angle of average velocity from the horizon

  Dtermine magnitude and direction expressed by the angle

the slider p can be moved by means of the string s while the slotted arm rotates about point o. the angular position

  Te volume of the air slowly decreases to 0002 m3 in a

air is contained in a vertical piston-cylinder assembly by a piston of mass 50 kg and having a face area of 0.01 m2.

  Using constant specific heats evaluated at 300 k determine

initially an insulated rigid tank contains 28.5 kg of water at 23.4oc and 101 kpa. the tank also contains a 3.14 kg

  Determine the deflection of the beam

What load P allow can be supported at the midpoint of the bar if the yield stress in the steel wires is 220 MPa and in the aluminium wire is 80 MPa? A saftey factor of n = 2 is needed.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd