User Account

All Pages

If the net power out is 70mw determine the mass flow rate

Assignment Help Mechanical Engineering
Reference no: EM13638051

An ideal Brayton cycle uses air as the working fluid and has a pressure ratio of 12. The compressor inlet temperature is 300K and the turbine inlet temperature is 1000K. If the net power out is 70MW determine the mass flow rate of the air using constant specific heats For: An ideal cycle When the compressor and turbine efficiencies are 85%.

Reference no: EM13638051

Questions Cloud

The ironiii chloride does not react with hydrochloric acid : a mixture containing ironiii sulfide and ironiii chloride isreacted with hydrochloric acid.fe2s3 6hcl --gt 2fecl3
Say a random variable x is drawn uniformly from between 0 : say a random variable x is drawn uniformly from between 0 and 1. say that y sin2pix. what is the covariance between x
How would you interpret the findings of a correlation study : how would you interpret the findings of a correlation study that reported a linear correlation coefficient of 0.3?a.
A meter stick is charged with 20 micro coulombs by placing : a meter stick is charged with 20 micro coulombs by placing it on a van de graff generator. assume that the charge is
If the net power out is 70mw determine the mass flow rate : an ideal brayton cycle uses air as the working fluid and has a pressure ratio of 12. the compressor inlet temperature
Two positive point charges q1 16 micro coulombs and q2 4 : two positive point charges q1 16 micro coulombs and q2 4 micro coulombs are seperated in a line by a distance of 3
A wall is composed of a 12-cm-thick layer of material a and : a wall is composed of a 12-cm-thick layer of material a and a 20-cm-thick layer of material b. the temperature of the
Consider an xy plane with charges located at the following : consider an xy plane with charges located at the following points q1 is located at x0 y0 and has a magnitude of 4 micro
Air from the surroundings enters the tank at a rate of 181 : a tank with a volume of 0.142 m3 is initially evacuated. the tank develops a small hole. air from the surroundings

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Acylindrical bar of steel e 209 gpa or 30 times106 psi v

a cylindrical bar of steel e 209 gpa or 30 times106 psi v 0.30 9.6 mm 0.3780 in. in diameter is to be deformed

  Water is pumped from a lake at ambient pressure

Water is pumped from a lake at ambient pressure

  Calculate the enthalpy change of the universe

calculate the enthalpy change of the universe during the process. Cp=Cv = 4.18 kj/kgK

  Draw a schematic of the ideal rankine cycle and the

an engineer has proposed that a simple ideal rankine cycle that uses refrigerant-134a be used to produce work with heat

  What is the final pressure c what mass fraction of the

a rigid container with a volume of 0.17m3 is initially filled with steam at 180kpa 340c. it is colled to 90c. a at what

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  Find a the partial pressures of the air and water vapor b

a space is at a temperature of 75 f 24 c and the relative humidity is 45 percent. find a the partial pressures of the

  An engine block with a surface area measured to be 090m2

an engine block with a surface area measured to be 0.90m2 generates a power output of 55 kw with a net engine

  Measuring fracture toughnessthe aim of this demonstration

measuring fracture toughnessthe aim of this demonstration is to use measurements of the load required to propagate a

  Carbon monoxide and water vapor h2o are placed in a

carbon monoxide and water vapor h2o are placed in a reaction vessel at 1000 k and 2.0 bars in a one two one molar

  A large number of concrete slabs each 06 m in length are

a large number of concrete slabs each 0.6 m in length are lined up with a spacing of 0.1nbspmm between them. the

  Measurements of the load required to propagate a crack

SEM212 - Aim of this demonstration is to use measurements of the load required to propagate a crack (tear) in packaging tape to determine its fracture toughness.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd