User Account

All Pages

If the maximum transverse shear force in the beam is 15 kn

Assignment Help Mechanical Engineering
Reference no: EM13640785

An aluminum extrusion (dimensions 50x60) with 5 mm thick walls is spot welded to a thin aluminum plate by a single row of welds. If the maximum transverse shear force in the beam is 15 kN, and if the maximum shear force each weld can resist is 5 kN, calculate the maximum allowable spacing between each weld.

Reference no: EM13640785

Questions Cloud

A find an expression for the velocity of the particle as a : the vector position of a particle varies in time according to the expression 5.60 - 6.80 t2 where is in meters and t
The mass of an empty container is 7635g the mass of : the mass of an empty container is 76.35g. the mass of thecontainer when filled with an unknown liquid d1.25gml
An engineer is going to redesign an ejection seat for an : an engineer is going to redesign an ejection seat for an airplane. the seat was designed for pilots weighing between
Transverse waves with a speed of 530 ms are to be produced : transverse waves with a speed of 53.0 ms are to be produced on a stretched string. a 4.45 m length of string with a
If the maximum transverse shear force in the beam is 15 kn : an aluminum extrusion dimensions 50x60 with 5 mm thick walls is spot welded to a thin aluminum plate by a single row of
A gas expands and does p-v work on thesurroundings equal to : a gas expands and does p-v work on thesurroundings equal to 287 j. at the same time it absorbs 216 j of heat from the
A 054 kg object connected to a light spring with a force : a 0.54 kg object connected to a light spring with a force constant of 21.0 nm oscillates on a frictionless horizontal
A steel plate which is 15 m by 15 m and 30 mm thick is : a steel plate which is 1.5 m by 1.5 m and 30 mm thick is lifted by four cables attached to its corners that meet at a
What is the speed vfinal of the electron when it is 100 cm : two stationary positive point charges charge 1 of magnitude 3.60 nc and charge 2 of magnitude 1.60 nc are separated by

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain horsepower and efficiency of three-phase motor

Horsepower and efficiency of three-phase motor, If a fully loaded 440V, three-phase motor draws 12.4 A at 86% power factor (pf). It's speed is 1730 rpm and its torque output to a mechanical load is 29.1 lb-ft x 1.356 = 39.5 Nm.

  Calculate the cycle thermal efficiency and the net work per

consider an ideal steam combined reheat and regenerative cycle in which steam enters the high-pressure turbine at 500

  If the total entropy of the cell must be ten times its

as a designer you are required to develop a new closed sealed thermal energy storage cell that has a maximum reversible

  The water is rapidly stirred until the pressure equals 40

a well-insulated rigid tank has a volume of 10ft3 water with a quality of 0.7 at 212of. the water is rapidly stirred

  The end of a robtoic arm extends along the path of the

the end of a robtoic arm extends along the path of the limacon r 1.5 cos thetam. at the instant that theta pi4 the

  What is the maximum percentage of steam that can be bled

a power plant is connected to a supply of 150 psia steam at 500 degrees f. the load is constant and requires throttling

  A gasoline engine receives air at 10 0c 100 kpa having

a gasoline engine receives air at 10 0c 100 kpa having compression ratio of 91 bynbspvolume. the heat addition by

  If the enthalpy of feedwater is 215 kjkg and the enthalpy

pressurized feedwater in a steam power plant is to be heated in an ideal open feedwater heater that operates at a

  Derive an expression for the work done on the gas it is a

an ideal gas p? mrt is heated at constant volume until its temperature is doubled and then cooled at constant pressure

  The picture below shows a system where superheated vapor

the picture below shows a system where superheated vapor enters a container at a flow rate of 90 kgs at 250c. the vapor

  A metal is being cast into a cylinder

A metal is being cast into a cylinder which is 10 cm in diameter and 20 cm tall. The mold is bottom-gated (see class notes for geometry)

  A curved nozzle assembly that discharges to the atmosphere

a curved nozzle assembly that discharges to the atmosphere is shown. the nozzle mass is 4.5 kg and its internal volume

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd