If the initial value of n is 1 millionl what values of k

Assignment Help Mechanical Engineering
Reference no: EM13613147

Suppose the rate of growth of a bacterial population (N cells/liter) is described by: dN/dt = kN -1000. The terms represent growth of the bacterial cells (with growth constant k), and predation (eating) of bacteria by a small population of protozoa which does not change over the time period of interest. Assume t is in seconds.

a. What are the units of k?

b. What are the units of the 1000 term on the right hand side?

c. If the initial value of N is 1 million/L, what values of k would allow the initial rate of change of N to be positive?

d. What Euler's method numerical simulation equation would you use to model this process?

Reference no: EM13613147

Questions Cloud

From the video barcelona restaurant group - managing human : from the video barcelona restaurant group - managing human resources determine how the hiring practices at barcelona
A 117-cm-long 300g string oscillates in its n 3 mode with : a 117-cm-long 3.00g string oscillates in its n 3 mode with a frequency of 180hz and a maximum amplitude of 5.00mm.
Find the desired radius and mass of the absorber if the : a cpva is attached to the crankshaft driven by a three-cylinder four-stroke engine which produces a maximum primary
Conducting sphere x is initially uncharged conducting : conducting sphere x is initially uncharged. conducting sphere y has twice the diameter of sphere x and initially has
If the initial value of n is 1 millionl what values of k : suppose the rate of growth of a bacterial population n cellsliter is described by dndt kn -1000. the terms represent
You are auditing the balance sheet section of a clients : you are auditing the balance sheet section of a clients balance sheet as of 12312011. you see that there is a 1000000
If my question of interest is if cactus needles are smaller : if my question of interest is if cactus needles are smaller the closer they are to a human trail what would be a good
Cortez corporation has analyzed their customer and order : cortez corporation has analyzed their customer and order handling data for the past year and has determined the
The distribution of a population of mechanical aptitude : the distribution of a population of mechanical aptitude test is normal with a mean of 46 and a standard deviation of 4.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Knowing the coefficient of kinetic friction between b and c

a 30 g bullet is fired with a horizontal velocity of 450 ms through 3-kg block b and becomes embedded in carrier c

  Explain the factor

explain the factor, which inhibit the use of a very high resolution and a large number of colors for display in the case of raster scanning display devices.

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  Calculate the engineering strain

A tensile specimen of cartridge brass sheet has a cross section of 0.320 in. × 0.120 in. and a gage length of 2.00 in. Calculate the engineering strain that occurred during a test if the distance between gage markings is 2.35 in. after the test.

  Calculate the magnitude of the principle stresses the

a steel shaft of radius r75mm is subjected to an axial compression p81kn a twisting moment t15.6kn.m and a bending

  Determine the final temperature and specific volume

Steam at 100 psia, 500oF is throttled to 20 psia. Changes in kinetic energy are negligible for this process. Determine the final temperature and specific volume of the steam.

  The corresponding magnitude of r

Two control rods are attached at A to lever AB. Using trigonometry and knowing that force in the right-hand rod is F2=20 lb, determine a.) the required force F1 in the left-hand rod if the resultant R of the forces exerted by the rods on the le..

  What will be the upsetting force required

A hot upsetting of stainless steel 316/316L, 2000mm dia disc, 200mm thickness is upset at 1200 degree Celsius to 150mm thickness. what will be the Upsetting force required to forge this disc and what will be the yield stress at this temperature.

  What is the maximum allowable pressure

What is the maximum allowable pressure if a factor of safety of 4 is to be used and what pressure would a strain of 40 pc indicate?

  Find out the largest couple that can be applied

Determining the largest couple that can be applied to a beam in pure bending. A beam of cross section shown is extruded from an aluminum alloy for which σy = 310 MPa and σu = 480 MPa.

  What should the bungee cords relaxed length

As shown, a 150 lb bungee jumper wants to jump from the top of a 630 ft high bridge and be able to just touch the water below. Given that the bungee cord has a spring constant of 108 lb/ft, what should the bungee cord's relaxed length, l, be for t..

  Estimate the design-stage uncertainty in determining the

estimate the design-stage uncertainty in determining the voltage drop across an electric heating element. the heater

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd