If the initial flow rate through the pipe is 12 ls

Assignment Help Mechanical Engineering
Reference no: EM13640345

Two water reservoirs A and B are connected to each other through a 40 m long, 2 cm cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve. The water level in both reservoirs is the same, but reservoir A is pressurized by compressed air while reservoir 2 is open to the atmosphere at 88 kPa. If the initial flow rate through the pipe is 1.2 L/s, determine the absolute air pressure on top of reservoir 1. Take the water temperature to be 10°C.

Reference no: EM13640345

Questions Cloud

Oxalic acid h2c2o4 is a useful primary standard for : oxalic acid h2c2o4 is a useful primary standard for standardizing solutions such as potassium permanganate kmno4. in a
Sat verbal scores are normally distributed with a mean of : sat verbal scores are normally distributed with a mean of 440 and a standard deviation of 96. use theempirical rule to
A solution of household bleach contains 525 sodium : a solution of household bleach contains 5.25 sodium hypochlorite naocl by mass. assuming that the density of bleach is
Classify these oxides as acidic basic amphoteric or neutral : classify these oxides as acidic basic amphoteric or neutral. p4o10 at2o7 al2o3 sno2 mgo li2o co no. begin by
If the initial flow rate through the pipe is 12 ls : two water reservoirs a and b are connected to each other through a 40 m long 2 cm cast iron pipe with a sharp-edged
The mean iq score of adults is 100 with a standard : the mean iq score of adults is 100 with a standard deviation of 15. use the empirical rule to find the percentage of
A 050 mol sample of oxygen gas is confined a 0deg c in a : a 0.50 mol sample of oxygen gas is confined a 0deg c in a cylinder. the initial pressure in the cylinder is 1.0 atm. if
The mean iq score of adults is 100 with a standard : the mean iq score of adults is 100 with a standard deviation of 15. use the empirical rule to find the percentage of
The beam of neutral hydrogen atoms with a speed of 104 ms : the beam of neutral hydrogen atoms with a speed of 104 ms along the x-axis enters a 1m long region where there is an

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd