If the gasnbspcontained in the tank is under a

Assignment Help Mechanical Engineering
Reference no: EM13344401

The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness 30 mm. If the gas contained in the tank is under a gauge pressure of 2 MPa, determine the normal stress developed in the wall of the tank and in each of the bolts. The tank has an inner diameter of 8m and is sealed with 900 bolts each 25 mm in diameter. 

Reference no: EM13344401

Questions Cloud

During an emergency launch operation to fill a missile with : during an emergency launch operation to fill a missile with rp-4 the volume of a well insulated fuel storage tank is
An electric pencil sharpener is rated 240 mw 6 v is : an electric pencil sharpener is rated 240 mw 6 v is connected to a 9-v battery and a series-dropping resistor rx
Carbon disulfide cs2 is a volatile flammable liquid it has : carbon disulfide cs2 is a volatile flammable liquid. it has a vapor pressure of 400.0 mmhg at 28.0degc and 760.0 mmhg
The voltage drops across three resistors in series are : the voltage drops across three resistors in series are measured to be 10.0v 15.0v and 25.0v. if the largest resistor
If the gasnbspcontained in the tank is under a : the spherical gas tank is fabricated bynbspbolting together two hemispherical thinnbspshells of thickness 30 mm. if the
Using the four basic application types introduced classify : using the four basic application types introduced classify the following system and explain your classification a
Give a proposed design and analysisnbspprincipal features : give a proposed design and analysisnbspprincipal features and working principle of any mechanisms using diagrams to
Phosphoric acid can be prepared by reaction of sulfuric : phosphoric acid can be prepared by reaction of sulfuric acid with phosphate rock according to the equation ca3po42
Develop a system to learn morse code the system will : develop a system to learn morse code. the system will have one input and 26 outputs one per letter. the user sends

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  You are to supply a design for an engine room crane

You are to supply a design for an engine room crane which will provide maintenance support for the main engine. Your design should include the rails the crane will sit on.

  Determine the greatest allowable steam pressure

the moisture content at the turbine exhaust is not to exceed 15%. determine the greatest allowable steam pressure at the turbine inlet and calculate the cycle efficiency.

  Evaluate the work required and the heat transfer

Kinetic and potential energy effects can be ignored. Evaluate the work required and the heat transfer, each in kW.

  Calculate the torque on each of the two shafts

Calculate the torque on each of the two shafts,the power transmitted and the power lost in friction. U=0.3 what is the efficiency of the drive.

  Sketch the cycle on p-v coordinates

Two kilograms of air within a piston-cylinder assembly execute a carnot power cycle with maximum and minimum temperatures of 750k and 300k, respectively.

  Determine the control resolution for this robot

The linear joint (Type L) of a certain industrial robot is actuated by a piston mechanism. The length of the joint wehn fully retracted is 600 mm and when fully extended is 1000 mm. If the robot's controller has an eight-bit storage capacity, dete..

  Determine the torque that can be applied to a solid

assuming that the solid shaft has been replaced by a hollow shaft of the same cross-sectional area and with an inner diameter equal to half of its own outer diameter.

  How many engagement point on flywheel would be necessary

How many engagement points on the flywheel would be necessary to make this machine safe

  Initially the container is divided into 2 equal parts using

consider a well insulated container of total volume v.a initially the container is divided into 2 equal parts using a

  What should the bungee cord''s relaxed length

As shown, a 130 lb bungee jumper wants to jump from the top of a 655 ft high bridge and be able to just touch the water below. Given that the bungee cord has a spring constant of 2.33 lb/ft, what should the bungee cord's relaxed length, l, be for ..

  Determine the missing property among p,t

Determine the missing property among P,T

  Compare with the efficiency of an otto cycle

Also, compare with the efficiency of an Otto cycle operating with the same maximum pressure.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd