User Account

All Pages

If the elevation points a and b relative to the elevation

Assignment Help Mechanical Engineering
Reference no: EM13621177

A contractor is required to prepare a soil surface so that its planar and the normal direction to the surface is within .5 degree of vertical. If the elevation points A and B, relative to the elevation at point c, are -3.3ft and -4.3 ft, determine the angle between the soil surfaces normal direction and the vertical, and if the surface is sufficiently level.

Reference no: EM13621177

Questions Cloud

The probability density function fx x8 exists for the : the probability density function fx x8 exists for the interval 3 lt x lt 5. what is probx gt
A tried-and-true revenue stream for large cities has been : a tried-and-true revenue stream for large cities has been the funds collected from parkingn meters. in a random sample
An american firm is evaluating an investment in mexico the : an american firm is evaluating an investment in mexico. the project will require purchasing equipment from a variety of
Determine the magnitude of his tangential acceleration at : tarzan m 85 kg is trying to swing across a river on a long vine. use angle 40 degrees and l10m. assume that he starts
If the elevation points a and b relative to the elevation : a contractor is required to prepare a soil surface so that its planar and the normal direction to the surface is within
The company is considering an expansion to double the : suppose the company in 1 is considering the following expansion projects. how would you calculate the required rate of
Suppose that x is a continuous random variable with : suppose that x is a continuous random variable with probability density function fx x18 over the interval 0 ? x ? 6.
A spinning wheel is initially spinning clockwise at a rate : a spinning wheel is initially spinning clockwise at a rate of 10 rads. it then begins to slow down with a constant
You may assume that the specific heats of the air are : air flows through a tube that has a throttling valve in it. if the tube is perfectly insulated perform a thermodynamic

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A particle moves along the curve yx2 - 4m with a constant

a particle moves along the curve yx2 - 4m with a constant speed of 5 ms. determine the point on the curve where the

  Estimate the schmid factor

Estimate the Schmid Factor, which is used to convert the CRSS into a critical tensile 'yield' stress. Use the measured angle between the slip trace and the sample long axis

  A variable force and appropriate energy transfers are

ten kilograms of water initially at 3000 kpa 200degc are contained in a piston-cylindernbspdevice shown below. a

  Determine the following a the boundary work for the

a piston cylinder device contains 0.25 kg of air initially at 1.8 mpa and 360 degc. the air is first expanded

  What input voltage will be computed by the adc

A successive approximation ADC has 4 bits and a reference voltage of 10 V. If the input voltage is 2.8 V, describe each step the ADC undergoes to determine the value of the 4 bits. What input voltage will be computed by the ADC?

  What is the design objective

2. What is the design objective? -to minimize the required power input to the compressors 3. What parameters does the design engineer control?

  This member is to be designed according to maximum shear

a solid square cross-sectional bar bxb with a yield stress of 250 mpa is subjected to a compressive axial force p 140

  What is the steam flow rate

If the cycle operates in steady flow with a power output of 20 kW, what is the steam flow rate?

  Calculate the force required in direct extrusion

Calculate the force required in direct extrusion of 1100-O aluminum from a diameter of 6 in. to 2 in. Assume that the redundant work is 30% of the ideal work of deformation, and the friction work is 25% of the total work of deformation.

  Develop a supplemental heat schedule as a function of the

the heat supplied by a heat pump used to maintain a buildings temperature is often supplemented by another source of

  Determine the minimum required wire diameter

A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 lbf). Determine the minimum required wire diameter, assuming a factor of safety of 2 and a yield strength of 860 MPa (12..

  Test the hypothesis that both machines fill to the same net

two machines are used for filling glass bottles with a soft-drink beverage. the filling process have known standard

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd