If the compressor consumes 19kw of power determine the

Assignment Help Mechanical Engineering
Reference no: EM13629034

A heat pump with refrigerant-134a as the working fluid is used to keep a space at 25°C by absorbing heat from geothermal water that enters the evaporator at 50°C at a rate of 0.051 kg/s and leaves at 40°C. The refrigerant enters the evaporator at 12°C with a quality of 15 percent and leaves at the inlet pressure as saturated vapor. If the compressor consumes 1.9kw of power, determine

a) The mass flow rate of the refrigerant

b) the rate of heat supply

c) the COP

d) the minimum power input to the compressor for the same rate of the heat supply

Reference no: EM13629034

Questions Cloud

What is the highest possible theoretical effeciency of a : what is the highest possible theoretical effeciency of a heat engine operating with a hot reseroir of furnace gases at
A nozzle receives 01 kgs of steam at 10 bar and 400 : a nozzle receives 0.1 kgs of steam at 10 bar and 400 degrees c with negligible kinetic energy. the exit is at 5 bar and
A boiler receives a constant flow of 5000 kgh liquid water : a boiler receives a constant flow of 5000 kgh liquid water at 50 bar and 20 degrees c and it heats the flow such that
Determine the work and heat transfer each in klkg of air : a compressor operates at steady state with air entering at 1 bar 20 deg celsius and exiting at 5 bar. a if the air
If the compressor consumes 19kw of power determine the : a heat pump with refrigerant-134a as the working fluid is used to keep a space at 25degc by absorbing heat from
A dean of a business school wants to know if the proportion : a dean of a business school wants to know if the proportion of graduates who use statistical inference within the first
A sperical conductor has a total charge q and radius r 1 : 1 the electic field between two large conducting plates is uniform 100.0 knc pointing from plate a to plate b. the two
Taking the average thermal efficiency to be 362 percent : in the recent years the united states produced 50.8 percent of its electricity in the amount of 1.6181012 kwh from
A 06-m-diameter hemispherical plexiglass bubble is to be : a 0.6-m-diameter hemispherical plexiglass bubble is to be used as a special window on the side of an above-ground

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A piston-cylinder device initially contains 035-kg of steam

a piston-cylinder device initially contains 0.35-kg of steam at 3.5 mpa superheated by 7.4degc. now the steam loses

  Compute the value of the corrosion potential how long do

lead experiences corrosion in an acid solution according to the following reaction pb 2h rightarrow pb2 h2 the rates

  Determine the pressure p2 and p3 in pipes 2 and 3 under the

water flows through the horizontal y-fitting shown in figure p3.101. if the flowrate and pressure in pipe1 are q1 2.3

  A man is driving his classic 1957 corvette on a circular

a man is driving his classic 1957 corvette on a circular path of radius r. the corvettes distancealong the paths

  Determine the instantaneous center of rotation

determine (a) the instantaneous center of rotation of the double pulley (b) the velocity of th slider block (c) the number of inches of cord wrapped or unwrapped on each pulley per second.

  The coefficient of performance of the air-conditioning unit

an air-conditioning unit takes in outside air at 46oc and 100 kpa having a relative humidity of 16. the air is cooled

  The system on site is a pressure sand filter with a service

the system on site is a pressure sand filter with a service curve. the filter is backwashed using the feed pump at a

  Calculate the battery failure probability under normal

a particulate monitor has a power supply consisting of two batteries in parallel. either battery is adequate to

  Determine the power required by the compressor and the rate

air with mass flow rate of 0.4 kgs enters an insulated compressor operating at steady state.determine the power

  Dtermine magnitude and direction expressed by the angle

the slider p can be moved by means of the string s while the slotted arm rotates about point o. the angular position

  Find the temperature at the interface

a. Find the temperature at the interface between the rod and sleeve and on the outer surface. b. What is the temperature at the center of the rod?

  Consider a system in which r 134-a is moved through an

consider a system in which r 134-a is moved through an evaporator. the evaporator removes energy from the the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd