User Account

All Pages

If the air exits to the atmosphere where the pressure is 85

Assignment Help Mechanical Engineering
Reference no: EM13613269

A nozzle is a device that is used to increase the velocity of a flowing fluid. It does this by reducing the pressure. Air enters a nozzle like that shown in the figure at a temperature of 195°C, pressure of 500 kPa, and a velocity of 100 m/s. Neglect heat transfer to the nozzle and potential energy change from the entrance to the exit. If the air exits to the atmosphere where the pressure is 85 kPa and temperature of 0°C, find a) the exit velocity, and b) the exit diameter.

Reference no: EM13613269

Questions Cloud

Dalyrymple company produces a special spray nozzle the : 1.budgeting provides all of the following except a means to communicate the organizations short-term goals to its
Assume that the internal energy and specific volume of : the pressure of 200 kgs of water is to be increased from 1 atm to 4 mpa. the water enters through a 20-cm-diameter pipe
Treat the sample results as simple random samples from : in one trip of a cruise ship 341 of the 3745 passengers became ill with norovirus. at about the same time 260 of the
How much energy must the water transfer to its surroundings : one way to keep the contents of a garage from becoming too cold on a night when a severe subfreezing temperature is
If the air exits to the atmosphere where the pressure is 85 : a nozzle is a device that is used to increase the velocity of a flowing fluid. it does this by reducing the pressure.
A company estimates that ordering costs are 200 per order : a company estimates that ordering costs are 2.00 per order picking costs are 1.00 per unique item ordered packing costs
Each of 106 identical blocks sitting on a frictionless : question 1 each of 106 identical blocks sitting on a frictionless surface is connected to the next block by a massless
The net income reported on the income statement for the : the net income reported on the income statement for the current year was 250000. depreciation recorded on fixed assets
What is the total work done to the system steam what is the : determine the heat transfer necessary to increase the pressure of 70 percent quality steam from 200 to 700 kpa

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Investigating a dynamic movement in polar coordinates

Investigating A Dynamic Movement in Polar Coordinates

  The pressure is held constant during the process while the

an insulated piston-cylinder device initially contains 0.3 m3 of carbon dioxide at 200 kpa and 27 ordmc. an electric

  Determine the rate of heat loss from the molten salt

Determine the rate of heat loss from the molten salt per meter length of the pipe.

  Heat is added at constant pressure until a temperature of

a cold-air standard diesel cycle has a compression ratio of 16 and begins compressing air isentropically from an

  Write down expressions for the normal strain and the true

write down expressions for the normal strain and the true strain for the following situation 1 in a tensile test where

  Water flows through a shower head steadily at a rate of

water flows through a shower head steadily at a rate of 10lmin. an electric resistance heater placed in the water pipe

  The uniform work platform which has a mass per unit length

the uniform work platform which has a mass per unit length of 21 kgm is simply supported by cross rods a and b. the

  Determine the change in the internal energy of the system

nitrogen at 100c and 600 kpa expands in such a way that it can be approximated by a polytropic process with n 1.2.

  What is the work required using the saturated liquid

saturated liquid water at 25 degrees c is pumped to a pressure of 5 mpa in an isothermal process. the specific work

  Is the heat transfer one two or three dimensional is there

consider a medium in which the heat conduction equation is given in its simplest form as 1r2 ddrr2dtdr 1a dtdt a. is

  Show that the force required to do this is equal to the

a uniform chain of total mass m and total length l lies in a heap on a table. one end is pulled upwards at constant

  If the plane starts to level off at t 40 s determine at

the flight path of a jet aircraft as it takes off is defined by the parametric equations x 1.25 t2 and y 0.03 t3

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd