If it takes 175 seconds for the dragster to reach 110 of

Assignment Help Mechanical Engineering
Reference no: EM13640134

Top fuel dragsters are some of the fastest accelerating vehicles on earth. After finishing their quarter mile run, a parachute deploys and they come to a stop within a few seconds. As a result of the extreme deceleration, drivers have been known to detach their retinas. Just thought that might be interesting. For the purposes of this problem, assume that the dragster crosses the finish line at a top speed of 333 mph and it has a weight of 2225 lbs.

a) if the acceleration is constant over the entire run, what is its magnitude? how long does it take the driver to complete the course?

b)assume that, after the dragster crosses the finish line, the engine cuts off and a parachute opens generating a drag force, Fd= AVx. draw a free body diagram of the dragster.

c)if it takes 17.5 seconds for the dragster to reach 1/10 of its top speed, what is the value of the constant, A

d) what is the peak magnitude of the acceleration experienced by the driver during the race?

Reference no: EM13640134

Questions Cloud

A wave pulse traveling to the right along a thin cord : a wave pulse traveling to the right along a thin cord reaches a discontinuity where the rope becomes thicker and
A card is drawn at random from a standard 52-card deck the : a card is drawn at random from a standard 52-card deck. the conditional probability that the card is a 2 given that a 2
Objects a b amp c make up a closed system a has a charge of : objects a b amp c make up a closed system. a has a charge of 53 c and is traveling east. b has a charge of 50 c and is
A mass vibrates back and forth from the free end of an : a mass vibrates back and forth from the free end of an ideal spring of spring constant 20 nm with an amplitude of .25
If it takes 175 seconds for the dragster to reach 110 of : top fuel dragsters are some of the fastest accelerating vehicles on earth. after finishing their quarter mile run a
A wave moves on a string with wavelength lambda and : a wave moves on a string with wavelength lambda and frequency f. a second wave on the same string has wavelength
Knowing that the tank has an outer diameter of 320 mm and a : a cylindrical storage tank contains liquefied propane under a pressure of 1.5 mpa at a temperature of 388c. knowing
Methane enters a heat exchanger at a volumetric flow rate : methane enters a heat exchanger at a volumetric flow rate of 120.0 m3min at a pressure of 1.013 bar and temperature of
A near-sighted person might correct his vision by wearing : a near-sighted person might correct his vision by wearing diverging lenses with focal length 55 cm. when wearing his

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd