If it is subsequently heated at constant volume until its

Assignment Help Mechanical Engineering
Reference no: EM13618591

Two kg of propane are initally saturated liquid at 0C. It undergoes an isentropic process that cools it to -40C.

a) What is the volume after the cooling?

b) If it is subsequently heated at constant volume until its pressure is 4bar, what is its quality after this heating?

c) What temperature and entropy is obtained at this final state?

d) sketch the processes described above on a p-v diagram and a T-s diagram.

Reference no: EM13618591

Questions Cloud

Check the assumption that compressive strength is normally : the compressive strength of concrete is being tested by a civil engineer. he tests 12 specimens and obtains the
Where r is measured in meters what is the total charge on : a spherical insulating ball with a radius of 3.0 cm has charges embedded in it with a volume charge density that
A what is the electric force that acts on the particle b : a uniform electric field has magnitude 260 nc and is directed to the right. a particle with charge 4.3 nc moves along
A matched pairs experiment compares the taste of instant : 1. a matched pairs experiment compares the taste of instant versus fresh-brewed coffee. each subject tastes two
If it is subsequently heated at constant volume until its : two kg of propane are initally saturated liquid at 0c. it undergoes an isentropic process that cools it to -40c.a what
A 950 kg boat is traveling at 110 kmh when its engine is : a 950 kg boat is traveling at 110 kmh when its engine is shut off. the magnitude of the frictional force fk between
A bird lands on a bare copper wire carrying a current of 15 : a bird lands on a bare copper wire carrying a current of 15 a. the wire is 8 gauge which means that its cross-sectional
What is the minimum temperature of the cold reservoir where : a refrigeration system has a coefficient of performance of 5. the heat rejection is an isothermal process at 37c. what
Assume a bank has 5 million in deposits and 1 million in : assume a bank has 5 million in deposits and 1 million in vault cash. if the bank holds 1 million in excess reserves and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The loading produes a gross nominal tension stress of 45

a very wide sheet of 7075-t651 aluminum plate 8mm thick is found to have a single-edge through-the-thickness crack 25

  Stoichiometrically how many kg of methanol are required for

biodiesel is produced from vegetable or animal oils. usually the glycerine in the oil is replaced by methanol. since

  Assuming that only caso3 is produced calculate the daily

assuming that only caso3 is produced calculate the daily production rate in tonsday of a 55-solids sludge from a

  Determine the angular velocity and angular acceleration

Block B of the mechanism is confined to move within the slot member CD. If AB is rotating at a constant rate of AB = 3rad/s, determine the angular velocity and angular acceleration of member CD at the instant shown.

  Why is communication with the customer so important

why is communication with the customer so important? explain the twin dangers of making many changes or not enough

  The discharge is located 20 ft 6 m higher than the entrance

500 galmin 30 ls of 100 degree f 40 degree c water flows through 300 ft 90m of 6-inch sch 40 steel pipe. the pipe

  Air enters an adiabatic diffuser at 320 k and 100 kpa with

air enters an adiabatic diffuser at 320 k and 100 kpa with a velocity of 642.9 ms. at the diffuser exit the temperature

  A what will be the resolved shear stress on the 11-1

a crystalline grain of iron in a steel plate is situated in such a way that a tensile stress of 100 mpa 14.5 ksi is

  If the us fleet of vehicles suddenly became 15 more fuel

if the u.s. fleet of vehicles suddenly became 15 more fuel efficient how much annual emissions of co2 would that

  If the density of the aniline is 1002 kgm cube and the

a centrifuge bowl with 250mm internal diameter is turning at 4000 rmin. it contains a layer of aniline 50mm thick. if

  Determine the initial discharge rate of water

The tank air pressure above the water level is 300kPa(absolute) while the atmospheric pressure is 100kPA. Neglecting frictional effects, determine the initial discharge rate of water from the tank.(Density of water=1000kg/m^3)

  Develop an algebraic expression in the form of an integral

a cross section of a rotating bearing is shown. the spherical member rotates with angular speed omega a small distance

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd