If condenser is water cooled and the inlet and outlet temps

Assignment Help Mechanical Engineering
Reference no: EM13636757

In a rankine cycle, steam from the boiler is at 6MPa and 500C and the condenser operates at 0.1 MPa. The turbine/turbines are 90% efficient and produce 100MW using a reheat at 1.0MPa back up to 440C.

a) determine the mass flow rate of steam

b)assuming the pump is 70% efficient, what is the Qin (heat in) for this system

c) if condenser is water cooled and the inlet and outlet temps are measured to be 15C and 60C respectively, what is the mass flow rate of the cooling water.

Reference no: EM13636757

Questions Cloud

Find the percent of volume change after a cube specimen is : if an isotropic material has a poissonamp39s ratio v. find the percent of volume change after a cube specimen is
If the wire which is fixed at both ends vibrates at its : a 26-cm-long wire with a linear density of 15 gm passes across the open end of an 87-cm-long open-closed tube of air.
An amount of sucrose a nonelectrolyte 34230 gmol is : an amount of sucrose a nonelectrolyte 342.30 gmol is dissolvedin 233.0 grams of water that increases the boiling point
Compute the boiling point of 30l of water that has 15 grams : compute the boiling point of 3.0l of water that has 1.5 grams of lithium fluoride dissolved in it. compute the
If condenser is water cooled and the inlet and outlet temps : in a rankine cycle steam from the boiler is at 6mpa and 500c and the condenser operates at 0.1 mpa. the turbineturbines
Find the magnitude and direction relative to due east of : a duck has a mass of 2.6 kg. as the duck paddles a force of 0.05 n acts on it in a direction due east. in addition the
Dtermine the work done by the shaftnbsp the work done in : pertains to vertical piston-cylinder assembly. a vertical shaft whose cross-sectional area is 0.8cm2 is attached to the
When the bungee jumper is reaching the end of his cord he : when the bungee jumper is reaching the end of his cord he begins to slow. while slowing down the direction of his
A group of students brought a six pack of beer to thebeach : a group of students brought a six pack of beer to thebeach in fortlauderdale fl. the six pack is placed in a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd