If air flows at a velocity of 5 ms calculate the local

Assignment Help Mechanical Engineering
Reference no: EM13640021

Air at 325 K and 70 kPa flows over the upper side of a 1-m-square plate. The upper plate is maintained at a constant temperature of 375 K.

(1) If air flows at a velocity of 5 m/s, calculate the local convection heat transfer coefficient at the trailing edge?

(2) If air flows at a velocity of 100 m/s, what will be the total heat lost by the upper plate.

Reference no: EM13640021

Questions Cloud

Determine 2 the head loss through nozzles 3 the efficiency : a dishwasher circulates water at a rate of 55 gpm with a small pump. the total head ppg v22g leaving the pump is
The speed of a nerve impulse in the human body is about 100 : the speed of a nerve impulse in the human body is about 100 ms. if you accidentally stub you toe in the dark estimate
If the weight of the empty tank is 50 lbs determine the : a large tank is used to calibrate the reading from a flow meter. measurements of the system weight as a function of
The elevator is moving upward with an acceleration of : a suitcase mass m 15 kg is resting on the floor of an elevator. the part of the suitcase in contact with the floor
If air flows at a velocity of 5 ms calculate the local : air at 325 k and 70 kpa flows over the upper side of a 1-m-square plate. the upper plate is maintained at a constant
What is the magnitude of the largest pushing force that can : a person pushes on a 57-kg refrigerator with a horizontal force of -270 n the minus sign indicates that the force
A standard 52-card deck is shuffled and 2 cards are picked : a standard 52-card deck is shuffled and 2 cards are picked without replacement from the top of the deck. the
A standard 52-card deck is shuffled and 2 cards are picked : a standard 52-card deck is shuffled and 2 cards are picked without replacement from the top of the deck. the
A rifle that shoots bullets at 500 ms is to be aimed at a : a rifle that shoots bullets at 500 ms is to be aimed at a target 46 m away and level with the rifle. how high above the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Use the systematic methodology to predict the amb generated

a thrust reversing system is used in jet engines to provide extra braking force to slow down an aircraft after a

  Two failures were recorded at the end of the 200 operating

thirty units were placed on test in order to estimate the reliability of the shift driver over a 200 operating hour

  In an orthogonal cutting operation the chip velocity was

in an orthogonal cutting operation the chip velocity was determined using a laser doppler velocimeter ldv as 80 of the

  A wellinsulated counterflow heat exehanger operates at

a wellinsulated counterflow heat exehanger operates at steady state. in one stream liquid water enters at 10 degree

  Determine the time required from the beginning of the first

a cnc drill press is to perform a series of through-hole drilling operations on a 1.75 in thick aluminum plate. each

  If the member is 1mm thick and the binary diffusion

a thin plastic membrane is used to separate helium from a gas stream. under steady-state conditions the concentration

  Find the exit temperature and volume flow rate assume the

two ideal gas with gas constant 0.287 kjkg.k flows are combined to a single flow in a mixing chamber. one flow is 1 m3s

  A long flat bar has the s-n diagram the bar is 6in wide by

a long flat bar has the s-n diagram. the bar is 6in wide by .5 in thick. it has a 2 in hole in the middle.a what is the

  Steam enters an adiabatic turbine at 2 mpa 300c and exits

steam enters an adiabatic turbine at 2 mpa 300c and exits at 50 kpa. the mass flow rate through the turbine is 2 kgs

  Cutting speed is 60mmin chip load is 025mmtooth and depth

explain the tapping operation and the steps to follow peripheral milling is performed on the top surface of a

  Plot the cost versus r for 2 le r le 10 m and determine the

a water tank consists of a cylindrical part of radius r and height h and a hemispherical top. the tank is to be

  Assume that in orthagonal cutting the rake angle is 20

assume that in orthagonal cutting the rake angle is 20 degrees and the friction angle is 35 degrees at the chip-tool

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd