User Account

All Pages

If a rod of 1025 steel 05 m 197 in long is heated from 20

Assignment Help Mechanical Engineering
Reference no: EM13345701

a)If a rod of 1025 steel 0.5 m (19.7 in) long is heated from 20 to 80 deg C (68 to 176 deg F) while its ends are maintained rigid, determine the type and magnitude of stress that develops. Assume that at 20 deg C the rod is stress free. 

b) What will be the stress magnitude if a rod 1 m (39.4 in) long is used?

Reference no: EM13345701

Questions Cloud

A solution containing 10 grams of an unknown liquid and 90 : a solution containing 10 grams of an unknown liquid and 90 grams of water has a freezing point of -3.33 degrees celcius
A man of mass m1 walks along a plank of length l with a : a man of mass m1 walks along a plank of length l with a constant acceleration a relative to the plank. the mass of the
You are the environmentalofficer attatched to pesticide : you are the environmentalofficer attatched to pesticide and toxic chemicals control board. prepare a technical brief
What is the work in joules done on the system to compress : what is the work in joules done on the system to compress he gas from 24.0 l to 12.5 l against a pressure of 1.5 atm at
If a rod of 1025 steel 05 m 197 in long is heated from 20 : aif a rod of 1025 steel 0.5 m 19.7 in long is heated from 20 to 80 deg c 68 to 176 deg f while its ends are maintained
Suppose i have a charge on an insulator if i touch it to : suppose i have a charge on an insulator. if i touch it to a conductor what happens? since charge doesnt flow on
A solution of ethanol c2h5oh in water is prepared by : a solution of ethanol c2h5oh in water is prepared by dissolving 58.0 ml of ethanol density 0.79 gcm3 in enough water
Calculate the molar enthalpy change when mercury is cooled : calculate the molar enthalpy change when mercury is cooled 10 k. the molar heat capacity of mercury is 27.8
Create a ladder program to control a washing machine this : create a ladder program to control a washing machine. this washing machine would have a fill cycle to one level a 10

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the radius of curvature of the path of the package

package is dropped from the plane which is flying with a constant horizontal velocity of vA = 150 ft/s at a height h = 1500 ft. Determine the radius of curvature of the path of the package just after it is released from plane at A.

  What is the percent span for the old and new setpoints

a reactor setpoint wasincreased from 160 psig to 190 psig. the reactor pressure transmitter was recalibrated from 0-200 psig to 0-300 psig. what is the percent span for the old and new setpoints?

  A cyclic steam power plant is to be designed for a steam

a cyclic steam power plant is to be designed for a steam temperature at turbine inlet of 360 celsius and an exhaust

  Calculate the velocity in the tunnel test section

A) Calculate the velocity in the tunnel test section. B) Compute the total pressure at the test section.

  Determine the magnitude t of the applied torque

The tank has a 180 mm inside diameter and a 12 mm wall thickness. Knowing that the tank contains compressed air under a pressure of 8 MPa, determine the magnitude T of the applied torque for which the maximum normal stress in the tank is 75 MPa.

  Determine the maximum speed

A vehicle of mass 1500kg and track 1.8m has a centre of mass located centrally at 1,1m above the ground. It has to travel around a bend of 56m radius to the centre of mass.

  Explain temperature change

explain temperature change (not conversion) is calculated from Celcius to Fahrenheit to Kelvin.

  Applied loads and young''s modulus and poisson''s ratio

Applied Loads, Young's modulus, Poisson's ratio, The Young's modulus and the Poisson's ratio for copper are 124.8 GPa and 0.36 respectively. When a tensile load is applie to a 1.5cm diameter copper rod

  If the resultant force middotr is directed along anbspline

if the resultant force .middotr is directed along anbspline measu red 75 clockwise from the positie x axis andnbspthe

  Use psychrometric chart to determine latent portion

Use Psychrometric chart to determine Latent portion

  Draw the block diagram of the uncontrolled seat

Draw the block diagram of the uncontrolled seat Plot the open loop displacement response of the uncontrolled seat to a step input

  Explain steady flow air compressor

A steady flow air compressor compresses 50 lb/min from 14 psia and 80 degrees F to a discharge state at 45 psia and 300 degrees F. Heat departs from the air only via circulating water that enters the jacket at 75 degrees F and leaves at 95 degrees..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd