I is suddenly exposed to an airstream of 10 degc with h

Assignment Help Mechanical Engineering
Reference no: EM13632379

A pure copper sphere with a diameter of 3.0 cm is initially at uniform temperature of 50 °C. It is suddenly exposed to an airstream of 10 °C with h = 15 W/m2-°C. How long does it take the sphere temperature to drop to 25 °C?

Reference no: EM13632379

Questions Cloud

The front of a jet engine acts as a diffuser receiving air : the front of a jet engine acts as a diffuser receiving air at 900 kmh -5degc 50 kpa bringing it to 80 ms relative to
A diffuser shown in fig p636 has air entering at 100 kpa : a diffuser shown in fig. p6.36 has air entering at 100 kpa 300 k with a velocity of 200 ms. the inlet cross-sectional
In a jet engine a flow of air at 1000 k 200 kpa and 40 ms : in a jet engine a flow of air at 1000 k 200 kpa and 40 ms enters a nozzle where the air exits at 500 ms 90 kpa. what is
A-2-m by 15-m section of wall of an industrial furnace : a-2-m by 1.5-m section of wall of an industrial furnace burning natural gas is not insulated and the temperature at the
I is suddenly exposed to an airstream of 10 degc with h : a pure copper sphere with a diameter of 3.0 cm is initially at uniform temperature of 50 degc. it is suddenly exposed
Suppose 500 g of hydrogen is separated into electrons and : suppose 5.00 g of hydrogen is separated into electrons and protons. suppose also the protons are placed at the earths
Assuming that the engine is made of iron and has an average : the combustion chamber of an internal combustion engine is at a temperature of 1100degc when fuel is burned in the
Steam at 260 c and 1 atm flow through an 8-in schedule-80 : steam at 260 c and 1 atm flow through an 8-in. schedule-80 steel pipe at a rate of 10000 lbhr. estimate the value of h
A charged particle a exerts a force of 260 micron to the : a charged particle a exerts a force of 2.60 micron to the right on charged particle b when the particles are 14.0 mm

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A ball is released from the bottom of an elevator which is

a ball is released from the bottom of an elevator which is traveling upward with a velocity of 6fts. if the ball

  Determine the exit temperature of the oil and the entropy

a well-insulated heat exchanger is used to heat water cp 4.18 kjkgk from 300 k to 90degc with a mass flow rate of 3

  Determine a suitable length for the bolt rounded up to the

a 1.5 inch thick steel plate and a 0.5 inch thick cast iron plate are compressed with 14- 20 unc grade 5 bolt and

  Determine the volume required to store 25kg of ethane at

determine the volume required to store 25kg of ethane at 320kpa and 35 degrees celsius. if the temperature rises to 65

  You are an engineer in an electric-generation station you

you are an engineer in an electric-generation station. you know that flames in the boiler reach a temp of 1200 k and

  Find the velocity of the wind

A plane can fly 305 mph in still air. If it can fly 185 miles downwind in the same amount of time it can fly 120 miles upwind, find the velocity of the wind.

  Calculate the contact forces at a and b

the 50-kg homogeneous smooth sphere rest on the 30 degree incline A and bears against the smooth vertical wall B. calculate the contact forces at A and B.

  When is the stress due to p of the same order of magnitude

a tapered structural steel column with a circular cross-section varies linearly from a radius of 25 mm to 15 mm over a

  Determine the moment of p about a

a 13.2-N force P is applied to the lever which controls the auger of a snowblower. Determine the moment of P about A when alpha is equal to 30 degrees.

  Calculate the specific volume of carbon dioxide 10 degrees

1. calculate the specific volume of carbon dioxide 10 degrees celsius and 80 quality?2. calculate the specific volume

  Basically a block is slid down from left side of the circle

basically a block is slid down from left side of the circle and when it reaches the middle of the bottom the speed of

  Explain beam deflection at corner through centroid

Beam deflection at corner through centroid, Sometimes the term centroid throws me for a loop. So, how would I set this problem up?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd