How you determined which improvement option to recommend

Assignment Help Mechanical Engineering
Reference no: EM131311242

Using the Arena Simulation from the class lecture given by Dr. Eseonu, identify the best combination of system improvements as measured by the increase in average monthly profit per dollar invested. You may not spend more than $4000 on changes. (Learning Outcome #2)

List the improvement options you tested and the increase in profit per dollar invested for each option tested.

Write a brief explanation of how you determined which improvement option to recommend.

Include a printed copy of the output sheet from Arena that shows the average number of good units produced in a month for the baseline (starting system) and for your final system with your recommended set of improvements.

Reference no: EM131311242

Questions Cloud

Where is the file stored : In a DHT-based network, assume node 4 has a file with key 18. The closest next node to key 18 is node 20. Where is the file stored?
Which web centric metrics would be most important to it : Now consider a content provider like CNN ( www.cnn.com). Which Web-centric metrics would be most important to it?
Federal guidelines governing a business e mail traffic : If you were to give advice to someone who had just started using e-mail, or even someone who's been using e-mail for a while, what would you tell that person should be the one guiding principle in all their e-mail communications?
Determine whether the router creates jitter for this class : Using time lines, show the arrival time, the processing duration, and the departure time for each packet. Also show the contents of the high-priority queue (Q1) and the low-priority queue (Q2) at each millisecond.
How you determined which improvement option to recommend : List the improvement options you tested and the increase in profit per dollar invested for each option tested.Write a brief explanation of how you determined which improvement option to recommend.Include a printed copy of the output sheet from Arena..
Calculate the pump pressure necessary for the given flow : 3-5 A water-tube steam generator operating at 2400 psia has 50-ft-high 3-in ID tubes. The pressure Drop is given by 3.25 x 10-6 m2, where m is the mass flow rate, in pound mass per hour Assuming sanzati water in the downcomer, a water-steam mixtu..
Pros and cons of notifying and not notifying possible victim : hat responsibility would you have to the people whose personal information was compromised? What are the pros and cons of notifying and of not notifying possible victims?
Write a paper about electrical engineering standards : You will write a paper about electrical engineering standards as they apply to communications. The topical coverage may be as specific or as broad as you want.
Increase production even more : Frank, his father notices this and advises Raymond to shutdown the stall, while Marie his mother advises him not only to set up the stall next weekend but to increase production even more. Raymond is extremely confused. Who do you think he should ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The compressor of a large gas turbine receives air from the

the compressor of a large gas turbine receives air from the ambient at 95 kpa 20degc with a low velocity. at the

  A triangular access port must be provided in the side of a

a triangular access port must be provided in the side of a form containing liquid concrete. determine the resultant

  Calculate the number of polyethylene chains

the total length of chains in the rope, assuming that carbon atoms in each chain are approximately 0.15 nm apart.

  Titanium is stiffer than aluminum has a lower thermal

titanium is stiffer than aluminum has a lower thermal expansion coefficient than aluminum and has a higher melting

  There are no significant changes in kinetic or potential

a gas within a piston-cylinder assembly undergoes a thermodynamic cycle consisting of three processesprocess 1-2

  Estimate the value of all of the ic chips

The processable area of each wafer is defined by a diameter = 270 mm. Estimate the value of all of the IC chips that could be produced, assuming an overall yield of 80% good product.

  Determine the heat transfer during the process

Determine the heat transfer during the process and the irreversibility of the process if the inner surface of the pressure cooker is constant at 250.°F.

  Determine the convection heat transfer coefficients

a 50 cm long 800 w electric resistance heating element with diameter .5 cm and surface temperature 120c is immersed in 60 kg of water temperature to 80c. also determine the convection heat transfer coefficients at the beginning and at the end of t..

  1 with reference to basic constructional features contrast

1. with reference to basic constructional features contrast the methods of compression employed by positive

  Determine the temperature of the air at the compressor exit

an air compressor operates at steady state with air entering at p11 bar t1 17 c and exiting at p25 bar. the air

  Calculate the boundary-layer thickness at the end of plate

Calculate the boundary-layer thickness at the end of the plate (for the two cases). Assume laminar flow (Blasius solution) and use seawater properties from Table 1.1.

  Temperature and cross flow velocity

For air at a temperature and cross flow velocity of Too = 25°C, V = 0.1 m/s, respectively, determine the surface temperature of the tube. The surround- ings temperature is Tsur = 25°C. For the conditions of part (a), plot the tube surface temperature..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd