How to use guass-jordan method to find a inverse

Assignment Help Electrical Engineering
Reference no: EM13230033

a) Write the system of linear equations in the form of Ax = b: (b) Use Guass-Jordan method to find A inverse (c) Use A inverse to solve the system of equations. -2x1 + x2 +x3 = -12 4x1 + 2x2 + 4x3 = 7 -x1 + x2 + 2x3 = -3

Reference no: EM13230033

Questions Cloud

What is the condition for matrix a to have inverse : (a) What is the condition for matrix A to have inverse Discuss this in terms of rank, determinant, linear dependence of rows and columns of matrix A, singular or non-singular. (b) Show that if A has inverse then AT also has inverse
What are some practical limits to economies of scale : What are some practical limits to economies of scale?
How many machines should be purchased to meet the upcoming : How many machines should be purchased to meet the upcoming year's demand without resorting to any short-term capacity solution?
Find a volume charge density px nd the flux through surface : 1. Point charges Q1 and Q2 are respectively, located at(4,0,-3) AND (2,0,1). If Q2=4nC, find Q1 such that a. E at (5,0,6) has no no z component b. The force on a test charge at (5,0,6) has no x component
How to use guass-jordan method to find a inverse : a) Write the system of linear equations in the form of Ax = b: (b) Use Guass-Jordan method to find A inverse (c) Use A inverse to solve the system of equations. -2x1 + x2 +x3 = -12 4x1 + 2x2 + 4x3 = 7 -x1 + x2 + 2x3 = -3
Find amplitude spectrum of dtmf signal ininfinite duration : A DTMF signal with duration T seconds can be modeled as a sum of two cosine signals with frequencies frand fc, multiplied by a rectangle function. For example, the DTMF signal for "1" is g1(t) = rect (t/T) * [cos(2pi*687t)+cos(2pi*1209t)]
What should the new organizational structure look like : What should the new organizational structure look like? Where should the systems manager put each manager?
What makes one campaign better than the other : Choose two advertising campaigns: one that you think is effective and one that you think is ineffective. What makes one campaign better than the other?
Find the system response due to the input : A digital system is described by the following difference equation: y[n] = x[n] - 0.3 x[n-1] + 0.28 x[n-2] Find the transfer function H(z), the denominator polynomial A(z), and the numerator polynomial B(z).

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the sacrifice ratio

Inflation in years 1-5 equals 3.1 percent, 2.2 percent, 1.6 percent, 1.3 percent, and 1.1 percent, respectively.

  What word length is required for an adc

What is the resolution of an ADC with a word length of 12-bits and an analogue signal input range of 100 V A sensor produces a maximum analogue output of 5V. What word length is required for an ADC if there is to be a resolution of 10mV

  Derive the transmission and reflection coefficients

Derive the transmission and reflection coefficients for the case of tunneling through a square potential barrier with 0

  Calculate the number of calls

i) Calculate the number of calls/hour/cell and the number of calls/hours/km2 ii) Calculate the number of users/hour/cell and the number of users/hours/channel iii) Find the modulation frequency for this system.

  Compare the one pole rc filters used in an active setup

1 To double the corner frequency in the low-pass and high pass two-pole filters, how would you change the values of the resistors and capacitors .2 Compare the one pole RC filters used in an active setup versus the passive setup

  What is difference between block diagram and front panel

What does the DAQ Assistant do How is it useful over the legacy acquisition methods What does FFT stand for and what does it do to a real-time signal Sketch the output of an FFT analysis performed on a 100 Hz sinewave signal at 1 V.

  Determine how many bits must the adc have

An LVDT with associated signal conditioning will be used to measure work-piece motion from -20 to +20 cm. The static transfer function is 2.5 mV/mm. The output will be interfaced to a computer via an ADC.

  Write a ladder logic program needed to implement

Write a ladder logic program needed to implement each of the following (assume inputs A, B and C are all normally open toggle switches).

  Determine the number of encoding levels required

A digital communications system is being designed with the goal of transmitting 32 kbits/s over a channel having a bandwidth of 8 kHz. Determine (a) the number of encoding levels required and (b) the minimum signal-to-noise ratio required in the c..

  Define infinity expected number of packets in the queue

If you have an M/M/Infinity system with arrival rate lambda and service rate mu(µ), how would you show that the expected number of packets in the queue is equal

  Develop an approach using the ite-operator

In other words, your approach should be able to answer the question whether two BDDs are complements of each other, without using the complement operation.

  Explain the concept of bit dominance used in can bus

A) Compare and contrast the following serial bus architectures: I2C, CAN, UART. Discuss the hardware implementation, communication protocol, and typical applications of each. B) Explain the concept of bit dominance used in CAN bus.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd