How to estimate the lifetime at degrees celcius

Assignment Help Electrical Engineering
Reference no: EM13261152

When a type of integrated circuit is tested at 185 degrees Celcius, 10% of the circuits fail within two weeks with VDD = 1.0V. Estimate the 10% lifetime at 95 degrees Celcius and 1.0V assuming Ea = 1.0eV.

Reference no: EM13261152

Questions Cloud

Compute the maximum energy stored in the inductor : A 12.0V dc battery having no appreciable internal resistance, a 146.5? resistor, an 10.6mH inductor, and an open switch are all connected in series. After the switch is closed, what is the maximum energy stored in the inductor
Find what is corresponding gate length for mos transistors : What is the (approximate) maximum electric field intensity for which constant mobility may be assumed for electrons in silicon. In a digital circuit with a supply voltage of 1V, what is the corresponding gate length for MOS transistors.
In what quarter did the current bearish/bullish market begin : Moving average oscillators are often used to determine when to buy and sell (or sell short) securities. They also can be used to help signal trends in the underlying data.
Find what is corresponding gate length for mos transistors : What is the (approximate) maximum electric field intensity for which constant mobility may be assumed for electrons in silicon. In a digital circuit with a supply voltage of 1V, what is the corresponding gate length for MOS transistors.
How to estimate the lifetime at degrees celcius : When a type of integrated circuit is tested at 185 degrees Celcius, 10% of the circuits fail within two weeks with VDD = 1.0V. Estimate the 10% lifetime at 95 degrees Celcius and 1.0V assuming Ea = 1.0eV.
Compute the ph at halfway to the equivalence : Consider the titration of 43.2mL of .240M HF with .220M NaOH. Calculate the pH at halfway to the equivalence point. Ka = 3.5 * 10^4
How many kilowatts hours of electricity could be generated : A solar pond consists of a thin layer of fresh water floating on top of a denser layer of salt water. When the salty layer absorbs sunlight it warms up and much of that heat is held there by the insulating effect of the fresh water above it
Explain how many pairs of degenerate pi-antibonding : In the molecular orbital model of the cyclopentadienyl cation, how many pairs of degenerate pi-antibonding molecular orbitals are there
Determine the index of refraction of the liquid : Light of wavelength 550nm in a vacuum is found to travel at 1.96*10^8m/s in a certain liquid. Determine the index of refraction of the liquid

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain the two possible frequencies

What are the two possible frequencies to which the local oscillator could be set? What bandwidth should the 10.7 MHz IF amplifier have?

  Determine what is the minimum inductance

We have four 3-H inductances. What is the maximum inductance that can be obtained by connecting all of the inductances in series and/or parallel What is the minimum inductance

  What is the time rate of change of voltage across capacitor

A constant current source of 2 mA is placed across a fully discharged capacitor of 100 F. In the time period before the capacitor reaches breakdown voltage, what is the time rate of change of voltage across the capacitor in V/s

  Characterize nature of the given response

For each of the following functions find the values of S & Wn (omega n) and characterize nature of response (overdamped,underdamped,critical damped,etc) a) G(s)= 225/ s^2 +30s+225 b) G(s)= 625/ s^2 +625

  What is the maximum number of consecutive bits

What is the maximum number of consecutive bits that are in error for a transmission through this channel if the data rate is 10Kbps? If the data rate is 11 Mbps?

  Design the circuit using mfb topology

determine the transfer function of a 4th order lowpass butterworth filter with a 3-dB cutoff frequency of 3.4 kHz and passband gain=1. Design the circuit using MFB topology. Design two sections with an order of 2.

  Derive the equations for the dynamic model for the motor

The resistance of the coil is .4 ohm. The inductance of the coil is 2.4e-4 H. The rotor inertia is 2.0e-5 kg m2. The current to torque gain is 0.06 Nm/A. The friction torque is 0.18 Nm. A 12 V voltage source is applied to the motor.

  For what values of f in range sinusoid produce same sample

The continuous-time sinusoid x(t) = cos(300?t) is sampled every Ts = 2.0 ms, so that x[n] = x(0.002n) For what other values of f in the range 0 Hz to 2.0 KHz does the sinusoid v(t)

  Explain plotting continuous time signal

Plotting Continuous time signal, Consider the following continuous signal: x(t) = 10e^-3t u(t) Using Matlab, plot the continuous-time signal over the range -1=

  Determine magnitude of the separating force acting on a line

Single-phase distribution line runs parallel to a ground line and is separated by 2m. During a short circuit, the distribution line experiences a current of 10,000A rms. Determine the magnitude of the separating force acting on a 1m section of the..

  Determine stability of closed loop system based on nyquist

Obtain polar plot using nyquist command. determine the stability of closed loop system based on nyquist criterion. design a compensator to meet the P.O. = 10%. Plot the before and after plot on the same nyquist plot.

  Calculate effective masses for conduction and valence bands

Draw energy band diagrams, for k lying between 0 and pi/a (take a=5Ã), for a material whose valence band follows the equation. and calculate the effective masses for conduction and valence bands.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd