How to convert the decimal numbers to binary numbers

Assignment Help Electrical Engineering
Reference no: EM13287807

convert the decimal +46 and +29 to binary, using thesigned-2's-compliment representation and enough digits to accommodate the numbers. Then Perform the binary equivalent of (+29)+(-49), (-29)+(+49), (-29)+(-49). convert the answers back to decimal and verify that they are correct.

Reference no: EM13287807

Questions Cloud

Find what percentage of the initial stored energy remains : an initially charged capacitence discharges through a resistance. At one time constant, what percentage of the initial voltage remains what percentage of the initial stored energy remains
Obtain the height of the final image : A diverging lens (f = -11.0 cm) is located 25.0 cm to the left of a converging lens (f = 36.0 cm). What is the height of the final image
Convert the string to bit form and decode the ascii code : the following string of ASCII characters whose bit patterns havebeen converted into hexadeciminal for compactness:73 F4 E5 76 E5 4A EF 62 73. of the 8 bits in eachpair of digits, the leftmost is a parity bit, the remaining are the ASCII code
Calculate the speed in the second segment : This seemed pretty straight foward but i get a bad anwser. In the solutions for this problem they just took the diameters, What is the speed in the second segmen
How to convert the decimal numbers to binary numbers : convert the decimal +46 and +29 to binary, using the signed-2's-compliment representation and enough digits to accommodate the numbers. Then Perform the binary equivalentof (+29)+(-49), (-29)+(+49), (-29)+(-49).
How long does it take for the second car to pass the first : What's the quickest way to approach this problem? A car is traveling at 80 km/h along the highway. How long does it take for the second car to pass the first
What are the required rates of return on the four stocks : At the time these betas were developed, reasonable estimates for the risk-free rate, RF, and the required rate of return on the market, R(Rm), were 6.5 percent and 13.5 percent, respectively.
Explain as tiltration and quantitative precipitation : when do we use melting point depression method to determine molecular mass vs. other methods such as tiltration and quantitative precipitation
Find the average power delivered to the tissues : A defibrillator consists of a 15.3-µF capacitor that is charged to 8.4 kV. What is the average power delivered to the tissues

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the motor phase currents and line currents

A three-phase 5 hp, 208 V motor has an efficiency of 92%, and a power factor of 0.87 (lagging) when it runs at full power. Calculate the motor phase currents and line currents if the motor is wye connected, and delta connected.

  What is the magnitude of the total circuit impedance

If an input signal with v(t) = 10 sin ( 2pi f 1592 t + 0º ) is applied to a series RL circuit with R = 1000-ohm and L = 0.1 H, what is the magnitude of the total circuit impedance

  What is the sampling period and the bit time

2. What is the sampling period 3. What is the bit time 4. What is the bit rate of that system 5. What is the time allotted to each channel

  Find synchronous motor current and excitation line current

A 460-V, three-phase,60-Hz system supplies power to a 10-kVA, delta-connected resistor load; a 50-kVA, 0.86 power factor induction motor, and a wye-connected synchronous motor that is operating at 0.62 power factor leading

  Find the canonical pos of thefunction f using minterms

Consider the function f(x1,x2,x3,x4)= (x1 + x2 + ~x3 + x4)(~x1+ x4) a. Find the canonical POS of thefunction F using minterms. b. Derive the simplest POS expressionof F using algebraic manipulation.

  How the resistors can be fabricated to non-standard values

You must design a three axis position indicator for the latest robot arm. Using no more than two operational amplifiers, design a circuit that uses three inputs, v1, v2, and v3 to produce an output signal vo=3 v1-2 v2-5 v3.

  Design a full-adder using only a minimum number of decoders

Design a full-adder using only a minimum number of 2x4 decoders. The complements of variables are not available but logic levels 1 and 0 are available.

  Calculate minimum number of bits that satisfies criteria

A signal, m(t) which is bandlimited to 20 KHz, is going to be transmitted over a channel a) If the stepsize must be less than  \(.002 m_{p}\) and the number of steps mut be a power of 2, calculate the minimum number of bits that satisfies this crit..

  Calculate the magnetic field intensity in amperes-meter

Model the line as an infinite filament of current under dc conditions. Calculate the magnetic field intensity in amperes/meter at the top of the head of a man who is 2 meters tall. Assume the man is standing on the ground directly underneath the l..

  Find the equivalent series network seen at input terminals

A load ZL is connected to the secondary of a linear transformer that is characterized by inductance's L1 = 1 H and L2 = 4 H and a unity coefficient of coupling. If w(omega) = 1000 rad/s, find the equivalent series network (R, L, and C values) seen..

  Find the current that flows in a silicon bar of 10-µm length

Find the current that flows in a silicon bar of 10-µm length having a 5-µm x 4-µm cross section and having free electron and hole densities of 105 / cm³ and 1015 / cm³, respectively, when a 1 V is applied end-to-end. Use µn = 1200 cm²/V·s and µp =..

  Define rain affects the downlink from the satellite

Rain affects the downlink from the satellite and the overall CNR ratio in the receiver falls by 6.0 dB to 13.0 dB. What is the bit error rate and the time between errors now?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd