Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
build a cicuit that must be able to operate a 3 amp load of the LED while being able to operate at voltages around 3V or 6V. It must be able to keep the LED on constantly while also being able to pulse the LED. Try not to use any resistors/voltage regulators or the such that that just turn the extra energy to heat ex( a 5V voltage regulator turns all the energy about 5V to heat in order to have a stable output of 5V)
Use MATLAB to compute the inverse Laplace transform of X(s)=(s^2+2s+1)/(s(s+1)(s^2+10s+50)) and determine the value of x(t) in the steady state. How would you be able to obtain this value without computing the inverse? Explain.
What is the effective data rate of this transfer (not counting the time for reading or writing the DVDs)?
Write an asm HCS12 program to flash LEDs on a dragon+ board three times when SW5 is pressed with a 5 kHz frequency, and 50% duty cycle clock signal. Generate a clock signal with 5 kHz frequency, and 50% duty cycle.
the upper critical frequency of anop-amps open loop response is 200Hz. If the midrange gain is 175,00, what is the ideal gain at 200Hz? what is th actual gain? what is the op-amps open loop bandwidth?
Assume that a receiver has a first amplifier stage with a 5KW input resistance, a gain of 300, an input audio signal of 20 mV, and an operating temperature of 27oC. When the amplifier is operating with a bandwidth first of 10 MHz,
given a sequence x(n), where x(0) = 4, x(1) =3, x(2) = 2, and x(3) =1 with the last two data zero-padded as x(4) =0, and x(5) = 0, evaluate its DFT x(k)
An AB latch operates as follows: If A = 0 and B = 0, the latch state is Q = 0; if either A = 1 or B = 1 (but not both), the latch output does not change; and when both A = 1 and B = 1, the latch state is Q = 1.
Design a hand warmer with a heated element consisting of an encapsulated resistor to be held in your hand and powered by a 6V battery that you put in your coat pocket. Use 26 gauge wire to connect the resistor to the battery.
A single phase transformer has the following rating: 120 kVA, 2000 V/100 V, 60 Hz with 1000 primary turns. Determine: (a) the secondary turns (b) the rated primary and secondary currents (c) the maximum flux
The shaft output of a three-phase 60- Hz induction motor is 80 KW. The friction and windage losses are 920 W, the stator core loss is 4300 W and the stator copper loss is 2690 W. The rotor current and rotor resistance referred to stator are respec..
Drift velocity the actual (physical) velocity of electrons along the wire. Transmission velocity the rate at which information can be transmitted electronically using conducing wires. How is it possible that the transmission velocity is so much faste..
For a Wien-bridge oscillator Given R = 20Kohm and C = 10nF what is the frequency of oscillation Given a required frequency of oscillation of f = 3kHz and R = 5kohm, what should the value of C be
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd