How the accuracy varies with the choice of the slice width

Assignment Help Mechanical Engineering
Reference no: EM131355261

Write a program that will calculate the location of the centroid of a semicircle (measured from the diameter line). This may be accomplished by dividing the area into slices of uniform width, either parallel or perpendicular to the diameter, and applying Equation (7.4). User input is to be the radius and width of the slice. Check the result with that obtained from Table 2. Note how the accuracy varies with the choice of the slice width.
Equation (7.4)

165_b0c75cff-11ac-4ea7-9f05-e07d7b9edbb4.png

Reference no: EM131355261

Questions Cloud

Read the chapters and give your reviews : Given that this is course is taught exclusively on line, you need to read and understand material that is presented. Please read Chapters 1 and 2 as indicated on the syllabus and then submit the five most important items found in each chapter. L..
Market for goods and services : Explain why "circular flow" between the market for goods and services, the labor market and the money market are crucial for macro-economic equilibrium.
Project will produce cash inflow : A project will produce cash inflows of $3,200 a year for 4 years with a final cash inflow of $5,700 in year 5. The project's initial cost is $9,500. What is the net present value of this project if the required rate of return is 16 percent?
Traditional principles of international peacekeeping : 350 words please list references How relevant are the traditional principles in the 21st century? What are the three traditional principles of international peacekeeping? Are all three still equally relevant today? Explain why and or why not.
How the accuracy varies with the choice of the slice width : User input is to be the radius and width of the slice. Check the result with that obtained from Table 2. Note how the accuracy varies with the choice of the slice width.
Analysts estimate that a bond has an equal probability : Analysts estimate that a bond has an equal probability of being priced at either $940 or $1,050 one year from today. The bond is also callable at any time at $1,020. What is the expected value of this bond in one year?
Western european countries : What are some reasons why the unemployment rate is typically lower in the United States as compared to Canada and some Western European countries?
Would you consider working for the national service corps : Would you consider working for the National Service Corps for financial compensation in another area, another community, or in a designated poverty area? Why or why not?
Customer survey for each market region : Customer Survey for each market region as a cross-tabulation (use pivot tables as appropriate), along with frequency distribution, histograms, and quatiles of these data.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Why is this problem simpler than for the turbulent boundary

consider heat transfer to a turbulent boundary layer with no pressure gradient or transpiration but with a vanishingly

  Calculate the cross sectional area in mm2 calculate the

the diameter of a round wire is d in mm. put d 3.00 mm using d 3.00mm and calculate the following calculate the cross

  What is the density of air leaving the compressor what is

a compressor takes in air at 100 kpa and 300 k and discharges it at 0.25 kgs at 1.2 mpa and 450 k. unfortunately the

  The bead is supported by a cable ac determine the force

a bead a weighting 2lb slides on a quarter-circular frictionless bar bc with radius. the bead is supported by a cable

  Explain the effect of fillers in altering polymer properties

Explain the effect of fillers in altering polymer properties? What are some of the main differences between thermoplastics and thermo sets?

  The capacity ratio k in the compressor and turbine is 14

in a gas turbine operating at a steady state air enters the compressor with a mass flow rate of 5 kgs at .95 bar and 22

  Temperature of the stack gas

Methane is completely burned with 20% excess air, with 30% of the carbon going to CO. What is the partial pressure of the CO in the stack gas if the barometer reads 740 mm Hg, the temperature of the stack gas is 300°F.

  What increase ?t in the temperature of the bar

What increase ?T in the temperature of the bar

  Determine the fuel consumption rate

An old gas turbine has an efficiency of 21 percent and develops a power output of 6000 kW. Determine the fuel consumption rate of this gas turbine, in L/min, if the fuel has a heating value of 42,000 kJ/kg and a density of 0.8 g/cm3.

  What is the percent span for the old and new setpoints

a reactor setpoint wasincreased from 160 psig to 190 psig. the reactor pressure transmitter was recalibrated from 0-200 psig to 0-300 psig. what is the percent span for the old and new setpoints?

  A 100kg pure iron block at 27 degrees c is dropped into an

a 100kg pure iron block at 27 degrees c is dropped into an insulated rigid tank that contains 0.1m3 of unused engine

  We''re asked to determine the deflection of a beam location

We're asked to determine the deflection of a beam location for a 2000N load. However the force is directed up the corner NOT centroid.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd