How tall must the antennas be if the link operates on a

Assignment Help Electrical Engineering
Reference no: EM13380011

How tall must the antennas be if the link operates on a frequency of 1450Mhz, D1=7miles, D2=11miles, and the obstruction is 85 feet high?

1909_Fresnel Zone Clearance.png

Practice Problem                              Fresnel Zone Clearance

 

1469_Fresnel Zone Clearance1.png

How tall must the antennas be if the link operates on a frequency of 2.450Ghz, D1=5miles, D2=11miles, and the obstruction is 60 feet high?

SOLUTION ALREADY PROVIDED FOR ALL OF THESE BELOW. JUST REWRITE IN OWN WORDS.

THIS ANSWER IS IN SOLUTION FILE - JUST REWRITE IN YOUR OWN WORDS PLEASE (FILE WILL BE UPLOADED IF PRICE IS AGREED)

637_Fresnel Zone Clearance2.png

1. How tall must the antennas be if the link operates on a frequency of 900Mhz and the total distance is 12 miles?  Heights are in feet above sea level and distance is in miles.  HAASLHA = 550 feet, HAASLHB = 545 feet, HAASLOBS-4.5mi = 545 feet, HAASLOBS-9mi = 545 feet.

2. What is the minimum height of Ha if Hb has to be mounted 60' above the calculated level?

1049_Fresnel Zone Clearance3.png

1. How tall must the antennas be if the link operates on a frequency of 2.450Ghz and the total distance is 18 miles?  Assume a 60' obstruction at each point of concern.  Heights are in feet above sea level and distance is in miles.  HAASLHA = 460', HAASLHB = 455', HAASLOBS-6mi = 480', HAASLOBS-10mi = 480'.

Obstruction at 6 miles                                                                            Obstruction at 10 miles

2. How much must HB increase if HA is limited to 2/3 of the equal tower height solution?

3. How must Ha and HB change to adjust for the terrain HAASL?

Reference no: EM13380011

Questions Cloud

1 a software project has been estimated to cost 1200000 and : 1. a software project has been estimated to cost 1200000 and take 14 months. given the average project outcomes from
How do you find and install good quality applications : how do you find and install good quality applications software? consider your own preferred approach while discussing
1 you are performing a path analysis of a 24 mile link : 1 you are performing a path analysis of a 24 mile link between two facilities. the path profile reveals three
Task1 compile a list of at least four skills that are : task1. compile a list of at least four skills that are listed as essential or desirable from the advertisments you have
How tall must the antennas be if the link operates on a : how tall must the antennas be if the link operates on a frequency of 1450mhz d17miles d211miles and the obstruction is
Description provided with 6 papers we have to critically : description provided with 6 papers we have to critically analyse those papers and make a document with usual report
1nbspnbspnbspnbspnbspnbsp : 1.nbspnbspnbspnbspnbspnbsp ipnbspnbspnbspnbspnbspnbspnbspnbspnbspnbsp 143.190.149.158 subnet mast nbspnbspnbsp
Sorting a list is a common example in computer science : sorting a list is a common example in computer science functional languages make it very easy to express a sorting
1 give syntax example for each of the following group : 1. give syntax example for each of the following group functionsavgsumminmaxcountdistinctstddevvariance2. provide 2

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the magnitude of the instantaneous current at 20usec

A charged 100- picoFarad capacitor has initial voltage across it of 10 V. A 100 kohm resistor is suddenly connected across the capacitor (at t=0) to discharge it. What is the magnitude of the instantaneous current at 20 usec

  Design a vdhl file controller to operate two separate sets

Design a VDHL file controller to operate two separate sets of three traffic light signals, one for each direction. Use eight LEDs as shown in to represent the outputs. The Time in This State can be met in several ways.

  How many bits are needed to appropriately digitize signals

Specify how many bits are needed to appropriately digitize each of the following signals. Choose from: 6 bits, 8 bits, 10 bits, 12 bits, 14 bits, or 16 bits. a. A signal where the maximum amplitude is 1 volt and the rms noise is 1.5 millivolts.

  How much charge is transported as a result of the charging

A constant current of 3 A for 4 hours is required to charge an automotive battery. If the terminal voltage is 10+ t/2 ,where t is in hours, a) How much charge is transported as a result of the charging

  Determine the ohmic value of the synchronous reactance

The Per-cent impedance of a single-phase electric load is 2.5. The base power is 100KVA, and the base voltage is 12.47KV. a find the per-unit impedance of the load if 400KVA and 20 KV are selected as base values.

  Describe does an equivalent rule exist for zeros

a). Without calculating E(z), find its poles. b). Give the rule that you used in part (a). c). Verify the results of part (a) by calculating E(z). d). Compare the zero of E(z) with that of E(s).

  Find atom in unstable state before it spontaneously decays

A sample of radiocactive material undergoes decay such that the number of atoms N(t) remaining in the unstable state at time t is related to the number No at t = 0 by the relation N(t) = No exp(t\tau)

  Calculate the voltage drop across the load

A simple power system consists of a dc generator connected to a load center via a transmission line. The load power is 100kW. The transmission line is 50km copper wire of 3 cm in diameter. If the voltage at the generator terminals is 400V

  Determine value of sampling period ts according the info

Supposed that the signal y(t) is low -pass filtered. The magnitud od the low pass filter is unity and the cut off frequency is Rz= 5000*pi rad/sec. Determine the value of the sampling period Ts according to the given information.

  Calculate the torsional spring stiffness constant for a

calculate the torsional spring stiffness constant for a steel shaft 0.5 in diameter and 2.5 ft long.express your result

  What are the conditions in terms of electrical parameters

Is it possible to interface an IC with a different technology such as TTL to HCS12 ports What are the conditions in terms of electrical parameters that need to be satisfied for this purpose

  Explain whats wrong with johns cancellation reasoning

One day, John and Amparo, a senior EE student, were trying to fix Jasmine's old-fashioned (projection) TV, which contained the circuit shown below, apparently with a bad connection. John said that the RLC series branch had an impedance of 1ohm

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd