Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A stereo draws 2.4A at 120V. The audio output power is 50W.a)how much power is lost in the form of heat in the system?b)what is the efficiency of the system
Design a length-5 FIR bandpass filter with an antisymmetric impulse response h[n], i.e.., h[n]= -h[4-n], where (0 less tahn or qual n and 4 is bigger than or equal n), satisfy the following magnitude response values.
Assume that the I bit for external hardware interrupt IRQ is enabled and is low-level triggered. Explain how this interrupt works when it is activated. How can we make sure that a single interrupt is not interpreted as multiple interrupts
Suppose that we are designing a cardiac pacemaker circuit. Thecircuit is required to deliver pulses of 1-ms durstion to the heartthat can be modeled as a 500-Ω resistance. The peak amplitudeof the pulses is required to be 5 V.
A generator uses a coil that has 110 turns and a 0.475 T magnetic field. The frequency of this generator is 43.0 Hz, and its emf has an rms value of 230 V. Assuming that each turn of the coil is a square (an approximation), determine the length of..
draw a gate level schematic of a 4bit ALU that can ADD, Subtract, and AND. include the use of an adder/subtractor unit consisting of 4 full adders, and 4-bit 2:1 mutiplexer. No diagrams, gate level schematic only.
design the controller and estimator so that the closed-loop unit step response to a command input has a rise time tr
Three balanced three-phase loads are connected in parallel. Load 1 is Y-connected with an impedance of 400+j300 Ohms per phase;[ load 2 is delta-connected with an impedance of 2400-1800j Ohms per phase; and load 3 is 172.8+j2203.2 kVA.
Design it to give an output that is 1/3 of the supply voltage. Furthermore, neither the power ratings of the resistors nor the current rating of the supply are to be exceeded. The voltage output of the divider must not change by more than 1% when ..
A MOSFET transistor is being used as a converter switch in a 100v system. It is switching at 50 KHz and has a linear transition time of 3us. The full load current is 40 amps. - How much average power is being wasted due to switching
A Si is doped with 10^14 boron atoms per cm3. For T=300 K and T = 470 K. Determine the position of Ei, compute Ef-Ei, and draw a careful dimensioned energy band diagram for the Si sample. Note for Si Eg=1.1 eV, mp*/mn*=0.71. ni=10^14 cm-3 at 470 K
A piston-cylinder device contains carbon dioxide CO2 (molar mass = 46 g/mol) as shown in the figure. The cross-section area of the piston is 0.25 m2 and the initial cylinder height is 50 cm. CO2 is initially at 40 bar and 500 oC (state 1).
If Vid is 20-mV peak-to-peak sine wave applied in a balanced manner but superimposed on Vcm = 0.5 V, what is the lowest value that Vdd must have to ensure saturation -mode for Q1 and Q2 at all times. Assume Vt = 0.5 V.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd