How much is the spring compressed in stopping the ore car

Assignment Help Electrical Engineering
Reference no: EM13247158

An ore car of mass 35000 kg starts from rest and rolls downhill on tracks from a mine. At the end of the tracks, 26 m lower vertically, is a horizontally situated spring with constant 3 × 105 N/m.
The acceleration of gravity is 9.8 m/s2 . How much is the spring compressed in stopping the ore car?

Reference no: EM13247158

Questions Cloud

Explain what is the percent yield for the reaction : What is the percent yield for the reaction if 65.0 g of iron(III) oxide produced 15.0 g of iron? b) What is the percent yield for the reaction if 75.0 g of carbon monoxide produces 85.0 g of carbon dioxide
Find the maximum downward acceleration : At the bow of a ship on a stormy sea, a crewman conducts an experiment by standing on a bathroom scale. Find the maximum downward acceleration experienced by the crewman
Compute the grams of indicated product produced : For each of the following reactions, calculate the grams of indicated product produced when 20.0 g of each reactant is used: a) 4Al(s)+3O2(g)-->2Al2O3(s) (Al2O3). b) 3NO2(g)+H2O(l)-->2HNO3(aq)+NO(g) (HNO3). c)C2H5OH(l)+3O2(g)-->2CO2(g)+3H2O(g) (H..
What is the total momentum of the wo blocks after collision : a 2.0-kg block is moving right at 1.0 m/s just before it strikes and sticks to a 1.0-kg block iniially at rest. what is the total momentum of the wo blocks after the collision
How much is the spring compressed in stopping the ore car : An ore car of mass 35000 kg starts from rest and rolls downhill on tracks from a mine. At the end of the tracks, 26 m lower vertically, is a horizontally situated spring with constant 3 × 105 N/m.
Find the force exerted by the seat on the child : A 39.0-kg child swings in a swing supported by two chains, each 3.10 m long, Find the force exerted by the seat on the child at the lowest point
Compute the moles of indicated product produced : For each of the following reactions, calculate the moles of indicated product produced when 3.00 mol of each reactant is used: a) 4Li(s)+O2(g)-->2Li2O(s) (Li2O). b) Fe2O3(s)+3H2(g)-->2Fe(s)+3H2O(l) (Fe). c)Al2S3(s)+6H2O(l)-->2Al(OH)3(aq)+3H2S(g) ..
How many unit should be shipped from manufacturing facility : How many units should be shipped from each manufacturing facility to each of the retail stores if cost is to be minimized?
Define a solution of ascorbic acid is prepared by dissolving : Ascorbic acid, HC6H7O3, also known as vitamin C, is a weak acid. It is an essential vitamin and an antioxidant. A solution of ascorbic acid is prepared by dissolving 2.00 grams in enough water to make 100.0 mL of solution

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Define design a synchronous counter using j-k flip-flops

Design of sync counter 0010 to 1101 using JK flip flops, Design a synchronous counter using J-K flip-flops that will count from 0010 to 1101 repetitively.

  Calculate the m3-h of total gas entering the reactor at stp

Pure ethylene (C2H4) and oxygen are fed to a process for the manufacture of ethylene oxide (C2H4O) C2H4 + ½ O2? C2H4O The process flow diagram is shown below. The catalytic reactor operates at 300 °C and 1.2 atm. Under these conditions

  Calculate the power dissipated in the device

An InP TED is 0.5 pm long with a cross sectional area of 10" cm2 and is operated in the transit-time mode.(a) Find the minimum electron density no required for transit-time mode.

  Determine the hv-side fuses needed to protect

Determine the HV-side fuses needed to protect a 3x140kVA, 12470/208 YNyn0 distribution transformer bank. Show and explain step by step the procedure you employ to solve this question. Use the type K and type T fuse curves

  Explain using diagram

If L=0.0053nH, C=15µF find the operating frequency of series LC circuit. What factors decides capacitance? Explain using diagram.

  Design a circuit that takes an input signal that can swing

For input signal voltages between these limits, the input should pass unaltered to the output. The peak current drawn from the input source may not exceed 1mA. You may use any circuit component we've studied except opamps.

  What kind of transistor has higher voltage gain

What kind of transistor has higher voltage gain, BJT or FET and why What kind of transistor has better noise response BJT or FET and why How about frequency response high frequency, FET or BJT Low frequency response, FET or BJT

  Resize lighting system assuming a lighting level at bench

An office building of 20,000 ft2 would then take 40,000 watts of lighting at 2 watts /ft2. which amounted to 667 - 60 watt light bulbs or about the same two-bulb fluorescent fixtures. Resize the lighting system (W) assuming a lighting level.

  Nibco''s big bang - an sap implementation

Analyze Case Study - NIBCO's 'Big Bang': An SAP Implementation- Explain the pros and cons of the approach to implementation decided upon by NIBCO.

  Explain ideal job and goal of electrical engineer

Briefly explain your ideal job as electrical engineer? Why did you select this career? What goals do you have in this career? How do you plan to get these goals?

  Find zero state response if the input is given

1. Define the function f[n] = en/4 sin(n/10)u[n] using Matlab inline function. Plot this function using stem command over [5, 20]. 2. Use Matlab inline and stem functions to plot u[n] and delta[n] over [10, 10]. 3. find out what Matlab filter functi..

  Determine the frequency response function of the low-pass

design a 4th order Butterworth band-pass filter, using a low-pass filter followed by a high-pass filter, to extract the 1200Hz and 1500Hz components from the signal x(t) a. Determine the cut-off frequencies of the low-pass and the high-pass filters..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd