How much entropy is produced

Assignment Help Mechanical Engineering
Reference no: EM13719166

Air at 17oC and 200kPa is in a rigid, 2m3, insulated tank that has a paddle wheel in it. 733 kJ of work is put into the system by the paddle wheel. How much entropy is produced?

Reference no: EM13719166

Questions Cloud

Find the speed of the sled after the stuntman is on board : For a movie scene, an 80kg stuntman drops from a tree onto a 46kg sled that is moving on a frozen lake with a velocity of 10m/s toward the shore. find the speed of the sled after the stuntman is on board
Ideal gas model for the air and variable specific heats : Air at 300 kPa, 63oC, and a velocity of 423 m/s enters an insulated duct of varying cross-sectional area. The air exits at 150 kPa, 88oC. At the inlet, the cross-sectional area is 6.57 cm2.
Find the inward force necessary to provide each blades : If we model a blade as a point mass at the midpoint of the blade, what is the inward force necessary to provide each blade's centripetal acceleration
How much power will it radiate : A dish of hot food has an emissivity of 0.48 and emits 15 W of thermal radiation. how much power will it radiate
How much entropy is produced : Air at 17oC and 200kPa is in a rigid, 2m3, insulated tank that has a paddle wheel in it. 733 kJ of work is put into the system by the paddle wheel. How much entropy is produced?
Find the ratio of this force to the skater weight : In short-track speed skating, the track has straight sections and semicircles 16 m in diameter. What is the ratio of this force to the skater's weight
Obtain how much work does the tension force do on the ball : A rope is attached to a ball, and then the ball is swung with constant speed in a horizontal circle of radius 1 m. If the tension in the rope is 100 N,  How much work does the tension force do on the ball
Estimate how much work is done by friction : A 10 kg block is dragged by an unknown force for 10 m along the floor. The coefficient of kinetic friction between the block and the floor is 0.2. How much work is done by friction
Spare plants and become autotrophs like plants : Are there any other palatable inorganic acids other than phosphoric acid -  spare plants and become autotrophs like plants

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the mass flow rate of steam

Steam enters a diffuser at 20 psia and 240oF with a velocity of 900 ft/s and exits as saturated vapor at 240oF and 100 ft/s. The exit area of the diffuser is 1 ft2. Determine (a) the mass flow rate of steam and (b) the rate of entropy generation.

  Calculate the elastic modulus of this material

A cylindrical specimen of some metal alloy 8.7 mm in diameter is stressed in tension. A force of 1390 N produces an elastic reduction in specimen diameter of 0.0041 mm. Calculate the elastic modulus (in GPa) of this material if its Poisson's ratio is..

  At the beach atmospheric pressure is 1025 mbar you dive 15

at the beach atmospheric pressure is 1025 mbar. you dive 15 m down in the ocean and you later climb a hill up to 250 m

  Calculate the head loss in this length of pipe when the

a fluid flows in a certain length of cast iron pipe of 30 cm diameter with a mean velocity of 2.5 ms and head loss of

  A steel shaft 120 mm in diameter is supported in flexible

a steel shaft 120 mm in diameter is supported in flexible bearings at its ends. two pulleys each 500 mm in diameter are

  Potential energy is gained due to change in height

A tank at an elevation of z1 = 15 m contains 0.005 kg of saturated liquid H2O at T1 = 200 C and is attached to a paddle wheel. Take the reference state to be T0 = 25 ?C and p0 = 101.3 kPa. Compute the exergy transfer due to the process and the amount..

  If chilled air enters a 15m long duct at 70c what is the

a thin-walled uninsulated 0.3m diameter duct is used to route chilled air at 0.05kgs through the attic of a large

  Find the elevation of the pump relative to the reservoir

A fire truck draws water from an open constant-level reservoir through a hose of 0.2 ft2 cross section. The water is discharged from the pump through another 0.2 ft2 hose to a surge tank pressurized to 120 psig with air at the top. The pump adds 970 ..

  Explain why the two measurements give different values

A similar measurement is made applying the force parallel to one of the cube axes. Explain why the two measurements give different values of the elastic modulus.

  The coefficient of kinetic friction between sled and ice is

a sled of mass m is given a kick on a frozen pond. the kick imparts to it an initial speed of 1.70 ms. the coefficient

  A satellite in earth orbit has a mass of 108 kg and is at

a satellite in earth orbit has a mass of 108 kg and is at an altitude of 1.99 106 m.a what is the potential energy of

  Determine the quality of the refrigerant at exit of valve

Refrigerant 22 enters the valve of a refrigeration system with a pressure of 14 bars and a temperature of 32 C and exits at a pressure of 4 bars. Neglecting heat transfer and any changes in potential and kinetic energy, determine the quality of the r..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd