How much energy is stored in the flywheel at the end of 20s

Assignment Help Electrical Engineering
Reference no: EM13278292

A torque of 10 N.m is applied to a uniform disk shaped flywheel. The flywheel has a mass of 20kg and a radius of 0.5m. At t=0, the flywheel is at rest. How much energy is stored in the flywheel at the end of 20 sec?

Reference no: EM13278292

Questions Cloud

Design the metallurgical channel thickness of n-type silicon : Design (determine) the metallurgical channel thickness of an n-channel silicon JFET such that the pinch off voltage is -3.0V. The doping parameters are NA=3x1018cm-3 and Nd=2x101616 cm-3.
Explain what is the ph of the analyte solution : A 30.00 mL volume of a weak acid, HA, (Ka = 3.8 x 10^-6) is titrated with 39.00 mL of 0.0958 M NaOH to the equivalence point. What is the pH of the analyte solution before any base is added to it
Find the maximum speed in the vertical plane : A circular disk having a radius of 4 ft and weighing 40lb has a small weight of 20lb attached to it at a distance of 2ft from its center. If the disk is in the vertical plane and set in rotation about an axis through its center so that its minimum..
Explain ammonia reduces copper oxide to the free metal : At high temperature, ammonia reduces copper(II) oxide to the free metal: Step 1: 2NH3(g) + 6CuO(s) => N2(g) + 3Cu2O(s) + 3H2O(g)
How much energy is stored in the flywheel at the end of 20s : A torque of 10 N.m is applied to a uniform disk shaped flywheel. The flywheel has a mass of 20kg and a radius of 0.5m. At t=0, the flywheel is at rest. How much energy is stored in the flywheel at the end of 20 sec
Explain the equilibrium partial pressure of nh3 increases : or each of the following cases, briefly explain whether the action causes net reaction from left to right, right to left, or no net reaction. Also, state whether the equilibrium partial pressure of NH3 increases, decreases or stays the same. (a) i..
Find the final speed of the puck b and a after the collision : Hockey puck B rests on a smooth ice surface and is struck by a second puck A, which has the same mass. Puck A is initially traveling at 14.6 and is deflected 28.0 from its initial direction. Assume that the collision is perfectly elastic.
Explain the magnitude of the partial charges in hbr : Determine the magnitude of the partial charges in HBr given that the bond length is 1.41 angstroms and the dipole moment is 0.82 debye.
Explain the formation reaction of h2so4 : Which one of the following reactions occurring at 25 ?°C is the formation reaction of H2SO4(l) a. H2(g) + S(s) + 2O2(g) => H2SO4(l) b. H2SO4(l) => H2(g) + S(s) + 2O2(g) c. H2(g) + S(g) + 2O2(g) => H2SO4(l) d. H2SO4(l) => 2H(g) + S(s) + 4O(g) e. 2H..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate minimum number of bits that satisfies criteria

A signal, m(t) which is bandlimited to 20 KHz, is going to be transmitted over a channel a) If the stepsize must be less than  \(.002 m_{p}\) and the number of steps mut be a power of 2, calculate the minimum number of bits that satisfies this crit..

  What is terminal voltage of self-excited dc shunt generator

A self-excited DC shunt generator is delivering 20 A to a 100-V line when it is driven at 200 rad/s. It is known that Ra=1.0 ohms and Rf=100 ohms. When the generator is disconnected from the line, the drive motor speeds up to 220 rad/s

  Determine the stator current and the power factor

A three-phase, 2300-V, 60-Hz, cylindrical-rotor synchronous motor has a synchronous reactance of 10 ohms per phase and negligible armature resistance. The motor delivers 250 hp at a power angle of 20 electrical degrees, and the efficiency is 90%

  Locate nd specify appropriate sensor if it is to operate plc

A control system is needed to control a small shopping center parking lot lighting system and the exterior lighting for the building. The design specifications require that the parking lot lighting and the exterior lighting turn on at dusk automat..

  Determine the maximum power delivered to the flashlight

After t = 0, the current entering the positive terminal of a flashlight bulb is given by: i(t) = 2(1 - e^ -10t) A and voltage given by: v(t) = 12e^-10t V Determine the maximum power delivered to the flashlight.

  Determine will the load dissipate the same amount of power

Suppose a DC power source with a voltage of 50 volts is connected to a 10-ohm load. How much power will this load dissipate. Now suppose the same 10 ? load is connected to a sinusoidal AC power source with a peak voltage of 50 volts.

  What is the amount of power that the bulb consumes

A circuit has a Thevenin equivalent circuit with Vth = 12 Volts and Rth = 50 Ohms. The load resistance that gives maximum power transfer is :A 50 Ohm resistor is connected in parallel with a 100 Ohm resistor. Which of the following statements are tr..

  Design a counter with the sequence utilizing two flip flops

Design a counter with the sequence 0-3-2-1-0 utilizing two flip flops. Flip flop A (MSB) is to be a JK type and Flip Flop B (LSB) is to be a RS Flip Flop.

  Determine which is the best sensor

The following specification s are given for fours different temperature sensors. If the application requires a temperature variation of -50°C to 120°C and the measured value is -20°C, select the best sensor.

  Find the minimum sampling frequency of the a-d converter

our senior design team is designing a force sensor to measure a force signal and analyze the signal with a microcomputer (binary system). The analog force signal is between 10 N and 70 N and has the frequency bandwidth of DC - 1000 Hz.

  Find out built-in potential barrier and widths of depletion

A junction is an n region next to an intrinsic region, which can be represented as an ntype region to a p-type lightly doped region. At T= 300K, the doping concentrations in silicon are Nd =1018 cm-3 and Na= 1013 cm-3.

  Calculate the circuit current and ohmic value of resistor

If the voltage drop across the capacitor is 115 volts and the power taken by the circuit is 922 watts, calculate a) the circuit current, b) the ohmic value of the resistor, c) the line voltage, d) the circuit power factor

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd