Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Error correcting codes are widely used on satellite links that have a low overall CNR in the receiver. A particular link has a clear air overall CNR of 11.0 dB and overall CNR of 6.0 dB when rain is in the downlink path. The receiver implementation margin is 0.5 dB. Modulation on the link is BPSK.
The following questions are addressed
a. Using the graph of BER vs CNR for BPSK, estimate the BER in clear air and in the specified rain conditions when no error correction is used, and when convolutional encoding with k = 7 is applied to the transmission. The bit rate is the same in each case.
b. How much additional transmitter power would be needed to allow the link to use QPSK instead of BPSK so that the bit rate could be doubled?
c. If the transmitter power can not be changed, what change would have to be made to the receiving earth station to increase CNR by 3 dB?
A sinusoidal voltage wave of real amplitude B0, and frequency w, and phase constant B, propogate in the forward z direction toward the shorted load end in a lossless transmission line of characteristic impedance Z0.
A 4.8 mF capacitor has been charged to11 V. The energy storedin the capacitor is used to light up a 0.3 KOhm lamp. Find the current flowing through the lamp 2.1 sec after the switch was turned on.
It is believed that the etching may alter surface crack geometry (i.e., reduce crack length and increase the tip radius). Compute the ratio of the original and etched crack tip radii for an eightfold increase in fracture strength if two-thirds of ..
Design your concept of a device and describe its operation in terms of the topics in the course (solid states course). For example, maybe you can make a new type of solar cell based on semiconducting liquids
A tooling designer is designing a jig that will insert pins into the flip-up handles of a coffeemaker. The bin to hold the pins should hold enough pins for 3 hours' work before reloading. The engineering estimate for the rate of inserting the pins..
Plot the steady state torque-speed characteristic for Va = 100V, 60V, and 30V. Calculate the armature voltage to be applied in the steady state at the speed of 1500 rpm when the motor torque load require is 3 Nm.
Calculate an appropriate window size that can be used to support a window based ARQ protocol - Calculate the effective throughput
A potentiometer is used to measure the position of a shaft. theinput range of shaft position is from - 160o to +160o . the corresponding output range is from -20 to +20 v. what is the span of this position sensor
Three light bulbs are connected in series to a 100-V battery in a circuit. Each light bulb dissipates 30W, 40W, and 50W, Respectively. Find the current (I) through the light bulbs.
1.For an impedance equation, such as 15ohms + j60ohms, explain the steps to determine equivalent series and parallel circuits. 2.For a given parallel RC or RL circuit, explain how admittance, current, and phase would change
A microcontroller memory map shows 16K bytes of Flash EEPROM in memory space $C000-$FFFF and 1 K bytes of RAM in memoryspace $1000-$13FF. a- Give the range of addresses (in hex) suitable for locating the code.
An automobile battery has an open-circuit voltage of 13.6 V and a total internal resistance of 0.012 ohms. What is the terminal voltage of the cell when it is delivering 250 A to the starter motor
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd