How many turns should be would on the secondary coil

Assignment Help Electrical Engineering
Reference no: EM13261068

A nickel-iron ring withcross-sectional area 0.85cm2 is expected to be driven to itssatur-ation magnetization of 1.1T in a ?eld of 800 A/m. The ?ux density will be measured by an electronic ?ux integrator with input resistance of 1kOhm and an integrating capacitorof 10m F. How many turns should be would on thes econdary(?ux-measuring)coil to give an output signal of +5V as the ring sample is driven to+1.1 T?

Reference no: EM13261068

Questions Cloud

Find voltage at center node and current flowing out of leg : assuming a perfect diode, I have a small circut which has three legs joined at the center. One leg has a +12V supply and a 1K ohm resister. Second leg has a -16 Volt supply witha 2K ohm resister, and the third has a perfect diode, with a 4K ohm re..
How much energy was converted into heat on the way down : A 1051 kg coasts down a hill 40 m high with its engine off and the driver's foot pressing the brake pedal. How much energy was converted into heat on the way down
What is the cost of common stock : The risk-free rate is 6.7%, the market risk premium is 8.1%, and the stock's beta is 0.45. What is the cost of common stock (Ke)?
State what is the molarity of a sodium chloride solution : Aluminium (atomic mass 26.98 g/mol) crystallizes in a face-centered cubic unit cell. In addition, aluminium has an atomic radius of 143 pm. What is the density of aluminium
How many turns should be would on the secondary coil : A nickel-iron ring withcross-sectional area 0.85cm2 is expected to be driven to itssatur-ation magnetization of 1.1T in a ?eld of 800 A/m. The ?ux density will be measured by an electronic ?ux integrator with input resistance of 1kOhm
What is the net present value of this cash flow stream : If you receive $1,177 at the end of each year for the first three years and $4,724 at the end of each year for the next three years. What is the net present value of this cash flow stream? Assume interest rate is 4.3%.
Compare field at center of helmholtz coil pair and solenoid : Compare the field at the center of a Helmholtz coil pair and at the center of a solenoid, if both use the same total length of wire and carry the same current.Take the solenoid length equal to the spacing between the Helmholtz coils
What is the speed of the skier : A skier is sliding downhill at 5 m/s when she reaches an patch on which her skies move freely with neglegible friction. What is the speed of the skier at the bottom of the icy patch
What is the weight of preferred stock : If the market value of debt is $51,962, market value of preferred stock is $43,675, and market value of common equity is 32,491, what is the weight of preferred stock?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How much current is there through the resistor

a 10 ohm resistor is connected across a 12 v battery. How much current is there through the resistor?

  Find method to find appropriate values of lc

Vs=310 V (Vrms=219 V) at the input of bridge rectifier Need LC filter at the output of bridge which can provide 240 V +-10V DC, with 2 A constant current. find method to find appropriate values of LC which can provide these specification.

  Determine what is the terminating load impedance

Use Smith Chart: A 100 Ohm air-coaxial transmission line is measured to have an input impedance of 100 + j100 Ohms. If the system is operated at 100 MHz and is one meter long, what is the terminating load impedance

  Calculate lost torque-opper loss and efficiency

A 100V dc series motor has an armature resistance of 0.2 ohm and field resistance of 0.25 ohm. The motor runs at a speed of 600 rev/min when the shaft torque is 27.14 Nm. Friction and windage losses at this speed are 300W.

  Determine speed of the motor and motor torque

The speed of a 10HP, 230V, 1200 rpm separately excited DC motor is controlled by a 1-phase full-wave bridge converter. The rated armature current of the motor is 10 A. The armature resistance is 0.25 Ohm and the armature inductance is 10 mH.

  What would the relative sensitivity of the ir detector

what would the relative sensitivity of the IR detector be if you use FREQOUT to send a 35 kHz harmonic? What is the relative sensitivity with a 36 kHz harmonic?

  How the existence of interest groups affect public opinions

Identify how the existence of interest groups and political parties affect the public opinions of Texans. Is this affect beneficial or hinderances to the prinicipal of local control popular in Texas policy Why

  How 3-phase balanced short circuit fault at arbitrary bus

Assume we have an N-bus power system and we know the N x N zero-sequence, positive-sequence, and negative sequence matrices for the system. Write a MATLAB program to find the system bus voltages during a (a) 3-phase balanced short circuit fault at..

  Find out the minimum signal to noise ratio

Determine the minimum signal to noise ratio (s/n) in dB required in each communication channel to achieve a data rate of 270 kbps?

  Find the permittivity of a parallel-plate capacitor

Find the permittivity of a parallel-plate capacitor if its capacitance is 100 ?F, the dimension of each rectangular plate is 1cm by 0.5cm, and the distance between the plates is 1mm.

  Find the three quartiles and the interquartile range

A. determine the mean, variance, and standard deviation B. find the three quartiles and the interquartile range C. Prepare a box plot for the data and determine if there are any outliers present.

  Determine the line impedance of three-phase wye-wye system

In a balanced three-phase wye-wye system, the load impedance is 10+j10 ohm. The source has phase sequence abc and the line voltage Vab= 220

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd