How many turns of wire are required to produce a b-field

Assignment Help Electrical Engineering
Reference no: EM13284174

How many turns of wire are required to produce a B-field whosemagnitude is greater than or equal to 10-3[T] inside anair-wound solenoid that is 2 [cm] long and carries a current of 100[mA].

Reference no: EM13284174

Questions Cloud

What was the speed of the bullet prior to impact : a 28 kg rifle bullet at an unknown velocity buries itself in a 3.6-kg pendulum hanging on a 2.8-m long string, what was the speed of the bullet prior to impact
Calculate roe , eva, cash flows and provide a comparison : Calculate ROE , EVA, Cash Flows and provide a comparison
Find and sketch the spectrum of the information signal : (a) Find and sketch the spectrum of the information signal. What is the bandwidth of the information signal (choose an appropriatedefinition for the bandwidth in each case) (b) Write a time-domain expression for the modulated carrier.Include all kn..
What would be the default risk premium : You are considering an investment in a one-year gov't debt security with a yield of 5 % or a highly liquid corporate debt security with a yield of 6.5%. The expected inflation rate for the next year is expected to be 2.5%.
How many turns of wire are required to produce a b-field : How many turns of wire are required to produce a B-field whosemagnitude is greater than or equal to 10-3[T] inside anair-wound solenoid that is 2 [cm] long and carries a current of 100[mA].
Determine the maturity risk premium for the thirty-yr bond : If inflation is expected to average 1.5 % points over both the next ten yrs and thirty years, determine the maturity risk premium for the thirty-yr bond over the 10-year bond.
At what frequency will the aliased signal appear : If a lowpass filter with a DC gain of 1 and 3 poles, all at 3KHzis used as an antialiasing filter, at what frequency will the aliased signal ( 5KHz) appear abd wgat will be the amplitude of the aliased signal.
What is the resultant amplitude of the two waves : Two sinusoidal waves, identical except for phase, travel in the same direction along a string, what is the resultant amplitude of the two waves
What is the snr of the digitized signal if the adc is ideal : A 12-bit ADC with a Vref of 5V is used to digitize small signals with a quiescent value of 2.5V and a variation around 2.5 of +/- 100mV. What is the SNR of the digitized signal if the ADC is ideal

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the hole diffusion current density at x

The hole concentration in p-type GaAs is given by p=10^16 (1-x/L)/cm^3 for 0

  At what overdrive voltage is the mosfet operating

What is the maximum output resistance that the source follower must have if the output voltage is to remain within ±20% of nominal value. If the MOSFET has kn = 16 mA/V2, at what current ID must it be biased. At what overdrive voltage is the MOSFE..

  Find the current flowing through the lamp after the switch

A 4.8 mF capacitor has been charged to11 V. The energy storedin the capacitor is used to light up a 0.3 KOhm lamp. Find the current flowing through the lamp 2.1 sec after the switch was turned on.

  Find the per-unit reactance of each generator

Two generators are connected in parallel to the same bus bar and each has an inductive reactance of 10% on rating. Generator 1 is rated 2,500 kVA and 2.4 kV, and generator 2 is rated 5,000 kVA and 2.4 kV.

  Determine the frequency that sampling system will generate

A system samples a sinusoid of frequency 850 Hz at a rate of 250 Hz and writes the sampled signal to its output without further modification. Determine the frequency that the sampling system will generate in its output.

  What is maximum voltage if current is required to be bigger

A 50-cm-long copper wire with a cross-sectional area 1.2286x10^-10 m^2 is used to connect a voltage source and a device. What is the maximum voltage if the current is required to be not bigger than 5A

  Find what is direction of robot arm in closed loop system

The controlled variable in a closed-loop system is the direction of a robot arm. Initially, it is at 50o; then it is commanded to go to 15o. When the error is 10o for the first time, what is direction of the robot arm

  How does the relate to the clock frequency division

What is the modulus of this counter. How does this relate to the clock frequency division that this counter can provide. At what number does this counter reset to start the sequence over again.

  Compute the power loss in a transmission line

compute the power loss in a transmission line with a resistance of 0.05 ohms/mile. Compute the power loss if 500kW of power is transmitted from a power generating station to cities at distances of 20,30,40....100 miles at 100v and 200v.

  What is the rate of change of the elecric field strength

There is a current of 10 A in a resistor that is connected in series with a parallel plate capacitor. The plates of the capacitor have an area of 0.5m^2, and no dielecric exists between the plates. (a) What is the displacement current between the ..

  Find the maximum and minimum inductor currents

A buck converter has the following parameters: Vs = 24 V, D = 0.65, L = 25 uH, C = 15 uF, and R=10 ohm.The switching frequency is 100 kHz. Determine (a) the output voltage, (b) the maximum and minimum inductor currents

  Find the mmf required to get an air gap flux of lines

The core is made of cast steel. Find the MMF required to get an air gap flux of 60,000 lines. The cross sectional area of the center section and air gaps is 4 in^2. The remaining sections have a cross sectional of 6 in^2.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd