User Account

All Pages

How many pump stations would be needed for a pipeline

Assignment Help Mechanical Engineering
Reference no: EM13719891

200mm DN pipeline has to deliver 80m³/h of water at a discharge pressure of  5,550 kPa. Approximately how many pump stations would be needed for a pipeline 300km long?

Reference no: EM13719891

Questions Cloud

What changes about the waves patterns : On the water simulation, what does the crest (peak) of the wave look like in the top view? What does the trough look like, When you add two drips, what changes about the waves' patterns
Using the average-end area-method : Determine the quantity of asphalt and granular material required for the parking lot. The asphalt is 4 inches thick and granular material is 8 inches thick.
What is the pressure that the pump can deliver : 4 kW motor is driving an oil pump with an efficiency of 95% in a 10 mm diameter pipe. If the velocities of the fluid in the pipe is 1.8 m/s. What is the flow rate that the pump delivers?
Moles of the endo conformer are present in the effluent : Cyclopentadiene and cyclohexanone are combined in a reactor and undergo an addition reaction.  The adduct can either have an endo or exo conformation.  For the application your plant has only the endo conformation is desired.
How many pump stations would be needed for a pipeline : 200mm DN pipeline has to deliver 80m³/h of water at a discharge pressure of  5,550 kPa. Approximately how many pump stations would be needed for a pipeline 300km long?
Pole-vaulter is holding the vaulting pole parallel : A pole-vaulter is holding the vaulting pole parallel to the ground. the pole is 5 m long. The vaulter grips the pole with his right hand at the top end of the pole and with his left hand 1 m from the top end of the pole. the mass of the pole is 2.5 k..
Find the frequency of the radiation of maximum intensity : The walls of a blackbody cavity are at a temperature of 27oC. What is the frequency of the radiation of maximum intensity
A closed system consists of an ideal gas : A closed system consists of an ideal gas with constant specific heats that remain constant. The gas undergoes a process in which the temperature increases from T1 to T2.
The power developed by the turbine : A gas turbine has a mixture of 17% CO2 , 60% N2 and 17% H2O on a molar basis enter at 1800°R and 116 psi and a mass flow rate of 4.41 lbm/s. The gas expands through the turbine isentropic ally to a pressure of 14.7 psi and a temperature of 1112.4°R.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the head loss in this length of pipe when the

a fluid flows in a certain length of cast iron pipe of 30 cm diameter with a mean velocity of 2.5 ms and head loss of

  A piston-cylinder device initially contains 035-kg of steam

a piston-cylinder device initially contains 0.35-kg of steam at 3.5 mpa superheated by 7.4degc. now the steam loses

  Heat transfer between the compressor and its surroundings

refrigerant 134a enters a compressor operating at steady state as saturated vapor at -4 degc and exits at a pressure of

  Methane is completely burned

Methane is completely burned with 20% excess air, with 30% of the carbon going to CO. What is the partial pressure of the CO in the stack gas if the barometer reads 740 mm Hg, the temperature of the stack gas is 300°F.

  The mercury emerges as a saturated liquid at 04 psia

twenty lbmmin of mercury vapor enters a condenser at 800of 0.5 psia. the mercury emerges as a saturated liquid at 0.4

  What is the allowable minimum length of the ramp

If the ramp height is 2ft. Using the ada code, what is the allowable minimum length of the ramp?

  The pump draws 20 kw of power and operates at 50 efficiency

consider a pump that moves q0.1 m3s of oil s.g. 0.8 from an open reservoir through a 10 cm diameter pipe. the pump

  Determine the relevant nozzle areas to expand the gas to

the duct between the turbine and the exit nozzle of a motor is 0.6 m diameter. the gas has a stagnant pressure and

  The inlet to a nitrogen compressor is a pipe of 5cm

the inlet to a nitrogen compressor is a pipe of 5cm internal diameter its outlet is a pipe of 2 cm internal diameter.

  A mixture of 1 mol of h2o 2 mol of o2 and 5 mol of n2 is

a mixture of 1 mol of h2o 2 mol of o2 and 5 mol of n2 is heated to 2200 k at a pressure of 5 atm. assuming the

  Contrast the chase demand adjusting internal resources to

contrast the chase demand adjusting internal resources to match changes in demand and the level resource shifting and

  A piston-cylinder arrangement holds a thermally perfect gas

A piston-cylinder arrangement holds a thermally perfect gas at p1=100kPa and T1 = 300K. Assume that cp = 1.0035 kJ/kg-K, cv = 0.7165 kJ/kg-K, and R = 0.287 kJ/

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd