Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A typical nuclear reactor generates 1,000 MW (1,000 MJ/s) of electrical energy. In doing so, it produces 2,000 MW of "waste heat" that must be removed from the reactor to keep it from melting down. Many reactors are sited next to large bodies of water so that they can use the water for cooling. Consider a reactor where the intake water is at 18° C. State regulations limit the temperature of the output water to 30° C so as to not harm aquatic organisms. How many liters of cooling water have to be pumped through the reactor each minute?
The resistance of the coil is 0.2 ohm. The inductance of the coil is 1.2e-4 H. The rotor inertia is 1.0e-5 kg m2. The current to torque gain is 0.03 Nm/A. The friction torque is 0.09 Nm. A 12 V voltage source is applied to the motor.
Design a sequential system to continuously output your set of eight different digits (01275438) in binary at the rate of one digit per clock pulse.
C program: counting numbers between 0-9, Write a C program that generates one hundred random integers between 0 and 9 and displays the count for each number.
Determine the number of gates needed to implement an eight-bit carry-lookahead adder assuming that the maximum fan-in for the gates is four.
Make a sketch of the band diagram for an n-type semiconductor and a p-type semiconductor doped with phosphorus and boron at 5*10^15/cm^3 respectively. Label all the features of your drawing, as well as the relative energy
in a hydroelectric generating station the difference in level between ,the water surface and turbine driving the generators is 425 meters.if 1250 liters of water is required to generate 1 kwh of electric energy.find the overall efficiency
A composite has a cross-sectional area of 320 mm2 and is subjected to a longitudinal load of 44,500 N. The continuous and aligned fiber-reinforced composite is to be produced consisting of 30 vol% aramid fibers and 70 vol% polycarbonate matrix.
A 10 uH inductor is connected to a circuit such that prior to t = 0 the current through the inductor is 10 mA. After t = 0 the current through the inductor is iL(t) = 10e^(-1000t) mA where t is time in seconds. a) Determine the expression for indu..
one group of students made an error by using HCLinstead of H2SO4 to titrate an unknown solution of NaOH. Would this error change the calculated molarity of the NaOH solution.
A three phase Y-connected 220-Volt 10-Hp, 60Hz, 6-pole induction motor has the following constants in Ohms per phase referred to the stator. R1=0.294, R2=0.144, X1=0.503, X2=0.209, Xm=13.25.
A system has the following input/output relation: y(n) = x(n) + .5 y(n -1). If the input x(n) is the sinusoidal signal shown in problem 1.32(d) (Above), the steady-state output will have the following form: y(n) = A sin(Bn+C). Determine the value ..
Two homogeneous isotropic dielectrics meet on plane x=0. For x > 0, Er1=6 and for x 0. Find: a) E2 for x
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd