How many clock cycles does it takes to reach location

Assignment Help Electrical Engineering
Reference no: EM13258642

memory location instruction

0 OUT O

1 INC

2 JC 1

3 JMP 3

ASSUME THE NSC HAS A NEW INSTRUCTION CALLED INC (OPCODE = "11") THAT INCRMENTS THE CONTENT OF THE OUT REGISTER; THE INC INSTRUCTION DATA FIELD IS UNUSED. ALSO ASSUME THAT THE LOC INPUT IINPUT IS TIED TO THE COMPLIMENT OF THE DOUT[3] BIT

(LOCK = ~DOUT3). HOW MANY CLOCK CYCLES DOES IT TAKES TO REACH LOCATION 3?

Reference no: EM13258642

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Determine the value of the total circuit complex impedance

An input signal of 10V at 0o and a frequency of 1592 Hz is applied to a series RLC circuit with resistor R = 100 ohm, inductor L = 20 mH, and capacitor C = 200 nF.

  Determine the settings

Determine the settings Z1, Z2 & Z3 for the relay at B12.

  Find the voltage between the points integrating along a line

Given the electric field E=4xux+2yuyV/m find the voltage between the points A(2,0) and B(0,2) integrating along: (a) straight line AB; (b) broken line AOB, where O(0,0).

  How much are the power losses in the motor

a DC motor turns at a speed of 1460 rpm and produces an output torque of 3.0Nm. The DC voltage applied to the motor is 100V and a current of 5.1A flows through the motor. A. What is the efficiency of the motor

  How to obtain the coefficients of the predictors

Get digital still images and video sequences from the Internet, as needed. You can use color and/or gray-scale images. 2. Implement intra-frame DPCM . Start with a linear quantizer in the initial implementation.

  Find nd on n side

Built-in voltage for a Si p-n junction is tested to be 0.6 V, NA = 2 X 10^15 cm^-3 on p side. Find ND on n side. (Assume ni = 1 x 10^10 cm^-3; and k*T/q= 0.026 V)

  Design the combinational logic circuit for an elevator

Design the combinational logic circuit for an elevator controller such that the option to go up or down by only one floor is disabled. Assume that the building the elevator is in has 4 floors. Your inputs are the current floor and the next request..

  Define j-k flip flop circuit design

This solution shows how to work from a given circuit implementation (a J-K flip flop circuit design) to derive the Boolean Logic and in so doing so simplify such logic using Boolean Algebra rules

  Determine the magnitude of the armature current

A 440-V three-hase Y-connected synchronous motor has a synchronous reactance of 1.5 ohms per phase. The field current has been adjusted so that the torque angle is 28 degrees when the supplied power to the motor is 90kW.

  Determine what polarization has the transmitted wave

A circular polarized wave in air is incident on glass surface. The angle of incidence equals the Brewster angle. Refractive index of glass, n(glass) is 1.35. Find the following quantities 1) The Brewster angle. 2) The angle of refraction

  What is the moment of inertia of the door about the hinges

A sheet of plywood 1.39 cm thick is used to make a cabinet door 55.5 cm wide by 69.5 cm tall, with hinges mounted on the vertical edge. A small 181-g handle is mounted 45 cm from the lower hinge at the same height as that hinge.

  What frequency in hz corresponds to value of dft

Suppose a signal is sampled at 1 kHz and you compute the DFT of the signal using 1000 signal samples. What frequency in Hz corresponds to the 150th value of the DFT

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd