How many bits are needed to appropriately digitize signals

Assignment Help Electrical Engineering
Reference no: EM13275555

Specify how many bits are needed to appropriately digitize each of the following signals. Choose from: 6 bits, 8 bits, 10 bits, 12 bits, 14 bits,
or 16 bits.

a. A signal where the maximum amplitude is 1 volt and the rms noise is 1.5 millivolts.
b. A signal with a signal-to-noise ratio of 900 to 1.
c. A signal with a coefficient-of-variation of 0.4%.
d. A high-fidelity audio system (hint: a jack-hammer is about 50,000 times louder than a pin drop).
e. A black and white digital image (hint: under the best conditions, the human eye can differentiate about 200 shades of gray between pure black and pure white).

Reference no: EM13275555

Questions Cloud

Describe frequency components that exist in digital signal : Be sure to specify three things for each component: its digital frequency (a number between 0 and 0.5), its amplitude (in digital numbers, peak-to-peak), and its phase relative to the original analog signal (either 0 degrees or 180 degrees).
Attributes of supply chain management : Any system must have components in order to be successful. The supply chain system is no different. What are the four key attributes of supply chain management and how do /may they impact logistics?
What is the largest possible error in an individual reading : When the temperature is held constant, the digital display of thermometer A does not change, but the display of thermometer B randomly toggles between three to four adjacent readings (i.e., +/- 2 degrees). For the questions below, assume that the ..
What is the expected return on this investment : If Marlene's expectation are correct, what will the proce pf this bond be in 2 year? 3. What is the expected return on this investment? 4. Should this investment be made? Why?
How many bits are needed to appropriately digitize signals : Specify how many bits are needed to appropriately digitize each of the following signals. Choose from: 6 bits, 8 bits, 10 bits, 12 bits, 14 bits, or 16 bits. a. A signal where the maximum amplitude is 1 volt and the rms noise is 1.5 millivolts.
How many revolutions would the wheel have made during race : Over the course of a multi-stage 4080-km bicycle race, the front wheel of an athlete's bicycle makes 2.00 106 revolutions. How many revolutions would the wheel have made during the race
What is the 95 percent probability range of returns : Assume that for a period of time, long-term corporate bonds had an average return of 7.1 percent with a standard deviation of 10.2 percent. What is the 95 percent probability range of returns?
What is the cost of preferred stock : Preston Industries has a WACC of 11.48 percent. The capital structure consists of 60.4 percent equity and 35.4 percent debt. The aftertax cost of debt is 5.9 percent and the cost of equity is 14.60 percent. What is the cost of preferred stock?
How much time does this maneuver take : A gymnast is performing a floor routine. In a tumbling run she spins through the air, How much time does this maneuver take

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Give transient behavior cannot be modeled by having function

Give an example of an RC circuit whose transient behavior cannot be modeled by having a function generator with square wave output replacing the mechanical switch.

  Specify the functions realized by each function generator

a. Tablulate the truth table for an 8x4 ROM that implements these Boolean functions. b. Tabulate the PLA programming table for these functions. Minimuze the number of product terms. c. Implement this circuit using a PAL with 3 inputs, 4 outputs and 3..

  How much pressure in atmospheres must the submersible

Titan has numerous hydrocarbon lakes containing a mix of methane and ethane in unknown proportions. A small submersible vehicle will exlpore Kraken Mare, the largest lake.

  Define contains basic function in matlab files

Contains basic function in MATLAB files. Write MATLAB script(s) to plot the basic signals below in two subplots. The upper subplot should be a continuous waveform (don't do g) and the lower subplot should be a discrete plot.

  Find the inductance of the inductor

A 5mm-long 100W microstrip line with velocity factor of 0.4 is used to fabricate a resonator at 3GHz. It is connected to an inductor at one end. Determine whether the other end of the microstrip line should be short circuited

  Determine and plot the system output y

An analog LTIC system with impulse response function h(t) = u(t+1)-u(t-2) is presented with an input x(t) = t(u(t) - u(t-2)). (a). Determine and plot the system output y(t) = x(t)*h(t)

  Determine the power consumed by the device at t

a) the total charge in the device at t = 3 s, assume q(0) = 0 (round to three decimal places) b) the power consumed by the device at t = 1 s (round to three decimal places)

  Find line and load voltages n turns ratio and total apparent

A ideal transformer is rated at 4800/480 volt, at 75KVA. it is connected as a step down auto transformer. find the line and load voltages, turns ratio and total apparent, real and reactive power at full load and at 60% rated load at a power factor..

  Draw an equivalent circuit representing each of power system

Draw an equivalent circuit representing each of the following power system components, showing all the circuit parameters in each case: (i) Short transmission line (ii) Medium length transmission line (pi and T circuits) (iii) Synchronous generator

  Describe what type of damping is exhibited by v

the voltage v in a certain circuit is described by the differential equation 3v"+24v'+75V=0 a) determine the values of α and w0 b) what type of damping is exhibited by V(t)

  Estimate the total charge enclosed within the cube

a)apply gauss's law to find the total flux leaving the closed surface of the cube. b)evaluate - *D at v the center of the cube. c)estimate the total charge enclosed within the cube.

  Find the power being absorbed by the resistor

A current source of 12 cos 2000t A, a 200-ohm resistor, and a 0.2-H inductor are in parallel. Assume steady-state conditions exist. At t = 1 ms, find the power being absorbed by the (a) resistor; (b) inductor; (c) sinusoidal source.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd