How long will it take to raise the load with your design

Assignment Help Mechanical Engineering
Reference no: EM131392822

Design a speed-reducing planetary gearbox to be used to lift a 5-ton load 50ft with a motor that develops 20 lb-ft of torque at its operating speed of 1750 rpm. The available winch drum has no more than a 16-in diameter when full of its steel cable. The speed reducer should be no larger in diameter than the winch drum. Gears of no more than about 75 teeth are desired, and diametral pitch needs to be no smaller than 6 to stand the stresses. Make multi view sketches of your design and show all calculations. How long will it take to raise the load with your design?

Reference no: EM131392822

Questions Cloud

Find the arrangement that gives the smallest error : Determine all possible two-stage compound gear combinations that will give an approximation to the Naperian base 2.71828. Limit tooth numbers to between 18 and 80. Determine the arrangement that gives the smallest error.
Develop a summary of the main concepts from the article : Develop a summary  of the main concepts from the article. Do not duplicate the article's abstract. If the article describes a research study, include brief statements about the hypotheses, methods, results, discussion, and implications. If any te..
Design candidates demonstrate the knowledge and skills : Design Candidates demonstrate the knowledge, skills, and dispositions to design conditions for learning by applying principles of instructional systems design, message design, instructional strategies, and learner characteristics.
Show how a collection of these cells can be arranged : A single silicon photovoltaic cell is found to have an open-circuit voltage of 0.6 V and a short-circuit current of 15 mA in full sunlight. Show how a collection of these cells can be arranged to deliver 500 mW at 9.0 V into a load.
How long will it take to raise the load with your design : Make multi view sketches of your design and show all calculations. How long will it take to raise the load with your design?
The anticipated benefits of health insurance exchanges : The anticipated benefits of health insurance exchanges include all of the following except. More than half of the U.S. population is covered by employer group health insurance. One of the underlying reasons is that. Which of the following is not an e..
What pneumatic pressure is required on the small piston : What pneumatic pressure is required on the small piston of given Problem to produce the necessary force?- A hydraulic system uses pistons of diameter 2 cm and 40 cm. What force on the small piston will raise a 500-kg mass?
Component of strategy diamond maps most closely to issues : Have you heard of Business Strategy Diamond? Class, what component of the strategy diamond maps most closely to issues related to strategy implementation? Why
Find the variable represented by a question mark : Figure P9-2 shows a compound planetary gear train (not to scale). Table P9-2 gives data for gear numbers of teeth and input velocities. For the row(s) assigned, find the variable represented by a question mark.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  When is it necessary to use gnl over linear what is the

when is it necessary to use gnl over linear? what is the difference in formulation between gnl and linear? what is

  Find the maximum allowable value of l

The L76 × 76 × 12:7 angle section is used as a cantilever column of length L. Find the maximum allowable value of L if the column is not to buckle when the 12-kN axial load is applied. Use E = 200 GPa.

  Determine the current supplied if the final temperature is

a mass of 12kg of saturated refrigerant-134a vapor is contained in a frictionless piston-cylinder device at 240kpa. now

  Determine the voltage of the source

A piston-cylinder device contains 12 kg of saturated R-134a vapor at 3.2 bar. An electric source supplies 8 A current to a resistor within the cylinder for 4 minutes and there is heat transfer of 400 kJ to the system. During these energy interactions..

  Plot the magnitude of the velocity of the parasailer as a

some parasailing systems use a winch to pull the rider back to the boat. during the interval when q is between 20 and

  Determine the exit temperature in degrees

Steam at 3MPa and 400C enters an adiabatic nozzle steadily with a velocity of 40m/s and leaves at 2.5MPa and 300m/s. Determine the exit temperature in degrees C. the ratio of the inlet to exit area

  Consider a steam rankine cycle with superheat the maximum

consider a steam rankine cycle with superheat. the maximum temperature and pressure are 540 c and 60 bar and the

  Why the calculated value is lower than the tabulated value

Calculate the minimum mass of manganese that could be detected.

  Determine the mass flow rate of air through the turbine

An adiabatic gas turbine expands air at 1000 kPa and 500?C to 100 kPa and 150?C. Air enters the turbine through a 0.2-m2 opening with an average velocity of 40 m/s, and exhausts through a 1.09-m2 opening.

  Use tolerance limit calculation as basis for your judgment

A random sample of 12 shearing pins is taken in a study of the Rockwell hardness of the pin head. Measurements on the Rockwell hardness are made for each of the 12, yielding an average value of 48.50 with a sample standard deviation of 1.5.

  Hw much electricity does the pump consume the pump is 70

14 kgs of liquid water enters a pump at a velocity of 1 ms and at 1 atm pressure. it leaves the pump at a velocity of

  Use a control volume analysis of mass

Water in a cylindrical container is hanging by a rod from the ceiling at point O shown in the figure. The container is initially full, and initially displaced 20 degree . There is a hole in the bottom where water pours out and the top of the containe..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd