Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Uniaxial crystal in 2D. Write a 2D TM mode FDTD simulation in the x-y plane for a uniaxial crystal with no = 1.5 and ne = 2.
(a) Create a slab of this crystal material that spans y and covers two wavelengths in x, and align the optic axis with y. Launch an z plane wave from x = 0 incident on the slab at frequency 1 THz and use 20 grid cells per wavelength. Observe the polarization and amplitude of the transmitted and reflected waves.
(b) Repeat (a), but rotate the crystal in the y-z plane through angles of 15, 30, 45, 60, and 90 degrees, using the rotation matrix in Equation (11.18). How do the transmitted polarization and amplitude change?
A half-wave rectifier circuit with a 1-Kwload operates from a 12-v(rms) 60-Hz household a 5-to 1 transformer having a center-tappedsecondary winding. It use two silicon diodes that can be modeled tohave a 0.7-v drop for all currents.
How do you use the Cayley-Hamilton technique to find the state transition matrix and the state equation output y.
what size capacitor should be placed in series with the series combination of 800 ohms and 20mH to give an admittance whose magnitude is 1m/ohm at w=10k rads/s
Consider a zero-phase sine function, x(t), with frequency ?=1.3rad/sec. What is the minimum positive time shift needed to turn this function into a zero-phase cosine of the same frequency
A modulating signal consists of two sinusoidal components: 1 kHz and 3 kHz. The transmitter carrier frequency is 80 kHz. Assume in a SSB-USB modulated signal that the inserted carrier at the receiver is 200 Hz too high. Indicate the frequencies of..
experimentuse the transistor board provideddc analysisa1 connect a 15 volt supply to vcc and ground and accurately set
I)Design a circuit that gives you the following relation between input and output Vout = 2.17Vin + 5 Here are the constraints you need to work with: 1) Only one power supply that gives ±12V is available 2) Available op-amps run on ±12V
Which transistor bias circuit arrangement provides good Q-point stability, but requires both positive and negative supply voltages.
Develop a process by means of the module „formula interpreter" with which a sinusoidal input voltage with the amplitude I V of any frequency f always produces a sinusoidal output voltage with the fourfold frequency 4∗f. The output voltage should h..
The small identical conducting spheres have charges of2.0 x 10^-9C and - 0.5 x10^-9 Coulomb respectively. When they are placed 4 cm apart. what is the force between them If they are brought into contact and then separated by 4 cm
Two LTIC systems have impulse response functions given by h1(t)=(1-t)[u)t)-u(t-1)] and h2(t)=t[u(t+2)-u(t-2)].a) Carefully sketch the functions h1(t) and h2(t). b) Assume that the two systems are connected in parallel.
the cut-off frequencies of a series resonant circuit are 5400 Hz and 6000Hz. a. find the bandwidth of the circuitb. If Qs is 9.5 , find the resonant frequenciy of the circuit c. if the resistance of thecircuit is 2 ohms, find the value of Xl andXc at..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd