User Account

All Pages

Grown in the shape of a tensile bar

Assignment Help Mechanical Engineering
Reference no: EM13887193

A single crystal of aluminum was grown in the shape of a tensile bar with the [321] direction aligned with the tensile axis.

A. Sketch a standard cubic projection with [100] at the center and [001] at the North Pole and locate the [321] direction on this projection.

B. Which of the {111} slip system(s) would be most highly stressed when tension was applied along [321]? Show the slip-plane normal(s) and the slip direction(s) of the system(s) on your plot.

C. What will be the ratio of the shear stress on the slip system to the tensile stress applied along [321]?

Reference no: EM13887193

Questions Cloud

Crystal subjected to uniaxial compression : NaCl crystals slip on {110} slip systems. There are six systems of this type. Consider a crystal subjected to uniaxial compression parallel to z = [110].
Why did deloitte take flanagans actions so seriously : Why did Deloitte take Flanagan's actions so seriously? What do you think might have led Flanagan to make such poor professional and ethical decisions?
Stretched in tension applied parallel : Consider an aluminum single crystal that has been stretched in tension applied parallel to x = [100] (σ x = +250 kPa) and compressed parallel to y = [010] (σ y = -50 kPa), with σ z  = 0, where z = [001]. Assume that slip occurred on the (111) in the..
Probability distribution shows the company''s monthly demand : 1.The demand for Carolina Industries product varies greatly from month to month. Based on the past two years of data, the following probability distribution shows the company's monthly demand:
Grown in the shape of a tensile bar : A single crystal of aluminum was grown in the shape of a tensile bar with the [321] direction aligned with the tensile axis. A. Sketch a standard cubic projection with [100] at the center and [001] at the North Pole and locate the [321] direction o..
When are quasi-experimental studies appropriate : Which of the following independent variables are appropriate for a quasi- experimental design and why?
Define nominal exchange rate and real exchange rate : Define nominal exchange rate and real exchange rate
Did capitalism emerge in the city or the countryside : Did capitalism emerge in the city or the countryside? What ‘social property relations' were necessary for the development of capitalism? Why did they develop in agrarian communities? How do these differ from pre-capitalist relations according to W..
What defenses do auditors use in response to litigation : What defenses do auditors use in response to litigation? What actions can auditors take to minimize litigation exposure?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the power required to maintain the clean rooms

at steady state a refrigeration cycle maintains a clean room at 55of by removing energy entering the room by heat

  The pipe rise from tank to trough is 3 feet calculate the

1. water at 80degf flows from a storage tank through 550 feet of 6-inch nominal size cast iron pipe actual id 6.52

  The truck travels in a circular path having a radius of 50

the truck travels in a circular path having a radius of 50 m at a speed of 4 ms. for a short distance from s 0 its

  Compression of a refrigerant

Measured data for pressure versus volume during the compression of a refrigerant within the cylinder of a refrigeration compressor are given in the table below. Using data from the table complete the following:

  Calculate adiabatic flame temperature butane burning

Calculate adiabatic flame temperature butane (C4H10) burning in air at 298 k and 1 atm, assuming complete combustion and constant specific heats.

  Observing plastic deformationthe aim of this demonstration

observing plastic deformationthe aim of this demonstration is to make some observations of the surface relief produced

  Calculate the final pressure and volume of the system

The process and volume relation is given p=(8-4v)bar for a non flow process ,where V is in cubic meter.If 130kJ of work is supplied to the system,calculate the final pressure and volume of the system.Take the initial volume as 0.5 cubic meter.

  A horizontal aluminum rod 1 cm in diameter and 10 cm long

a horizontal aluminum rod 1 cm in diameter and 10 cm long has both ends maintained at 363 k. air at 293 k and 1 atm

  Draw the free-body diagram and write the corresponding

draw the free-body diagram and write the corresponding elemental equation for a spring element with the following

  Read the titled books drilling fluid engineering manual

read the titled books drilling fluid engineering manual. textbook prepared by m-i drilling fluids co.1998 halliburton

  If 002 kg leaks out and the temperature drops to 27oc find

carbon monoxide is initially in a 50 l tank at 210 kpa and 127c.a determine the mass of the gas in kilograms.b if 0.02

  Determine the amount of heat transfer q that must be done

a mass of m .24kg of steam is contained in a closed cylindrical container is compressed by a piston from initial

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd