Give appropriate analog signal conditioning to interface adc

Assignment Help Electrical Engineering
Reference no: EM13227960

A calibrated RTD with alpha = 0. 0041 / degree C, R = 306. 5 ohm at 20 degree C, and PD = 30 mW / degree C will be used to measure a critical reaction temperature. Temperature must be measured between 50 degree and 100 degree C with a resolution of at least 0. 1 degree C. Devise a signal-condioonirg system that will provide an appropriate digital output to a computer. Specify the requirements on the ADC and appropriate analog signal conditioning to interface to your ADC.

Reference no: EM13227960

Questions Cloud

Discuss the advisability of using modular assemblies : Discuss the advisability of using modular assemblies in manufacturing. (What are the advantages and disadvantages?) To what extent can these arguments be applied to service products?
Business-internal service system : Business-Internal Service System. Customers receiving the service are internal to the organization providing the service.
What is the potential increase in labor productivity : an operation has a 10% scrap rate. as a result, 72 pieces per hour are produced. what is the potential increase in labor productivity that could be achieved by eliminating the scrap?
Define aqueous solutions in order of increasing ph : Without doing detailed calculation, arrange the following 0.10 M aqueous solutions in order of increasing pH. Explain your ordering.
Give appropriate analog signal conditioning to interface adc : A calibrated RTD with alpha = 0. 0041 / degree C, R = 306. 5 ohm at 20 degree C, and PD = 30 mW / degree C will be used to measure a critical reaction temperature. Temperature must be measured between 50 degree and 100 degree C.
Discuss how technological innovation resulted in change : discuss how technological innovation resulted in change within your organization, whether it concerned processes, new products or services, or the technology itself (i.e. seminars to webinars). How does your organization compare with others within..
What does the concept of interactive design mean : What does the concept of interactive design mean for a service such as the adventure playground described here?
Explain all reacionts in order of increasing tendency : For each reaction, identify the acid-base conjugate pairs. Then rank all reacionts in order of increasing tendency for the reaction to go to completion (to the right)
Describe the four options highlighted in the case in terms : Describe the four options highlighted in the case in terms of their feasibility, acceptability and vulnerability.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is initial value if the overhead values were considered

write an 8051 program that would generate a 200khz, 50% duty cycle, square wave at P1.0.Use Timer 0 for the delay. Ignore the overheads cycles due to the instructions in the loop. Assume 12 MHz clock. All data must be hex.

  Explain why the short-circuit method for determining

Explain why the short-circuit method for determining the Thevenin resistance of a circuit cannot be applied if the circuit does not contain any independent current or voltage sources.

  At what temperature are the two carrier densities equal

At what temperature are the two carrier densities equal?

  At what time t2 has 50 percent of the initial energy stored

A 190-F capacitance is initially charged to 1190V . At t = 0, it is connected to a 1-k resistance.  a) At what time t2 has 50 percent of the initial energy stored in the capacitance been dissipated in the resistance

  How much current is flowing through the resistor

If I have a resistor that is 10 Ohms and has a voltage drop of 4.2 V, how much current is flowing through the resistor?

  List the three mitigation types

In the presentation, the presenter, Mr. Rob Tucker discussed three types of disturbance mitigation responses or measures. List the three mitigation types and give a short definition of each of the mitigation type.

  Find the total transmit signal

Consider an 8-user CDMA system. The data vector of all users is given by [1,1,1,1,-1,-1,-1,1]. Find the total transmit signal.

  Explain ideal job and goal of electrical engineer

Briefly explain your ideal job as electrical engineer? Why did you select this career? What goals do you have in this career? How do you plan to get these goals?

  Find the electric field intensity produced by charges

Find the electric field intensity at (0,0,75000) produced by 50,000 0.1 C charges along the x-axis spaced at 1 meter apart starting at (1,0,0) and 50,000 0.2 C chargers along the y-axis spaced at 1 meter apart starting at (0,1,0).

  Schematic for the logic to implement circuit using inverter

a) Draw the state diagram b) Draw the schematic for the logic to implement this circuit using Inverters, AND gates, OR gates and D flip flops. Use the reverse side and additional sheets if needed.

  Draw the admittance diagram

find the voltage E and the current Ir and IL in phasor form

  Calculate the optimum thickness of the layer

a. Calculate the optimum refractive index of a single layer thin film antireflection coating for the silicon air interface at this wavelength. b. Calculate the optimum thickness of the layer.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd