User Account

All Pages

Forms of internal energy of the motor

Assignment Help Mechanical Engineering
Reference no: EM13888156

An electric motor consumes 9.00 KJ of electrical energy in 1.00 min. If one third of this energy goes into heat and other forms of internal energy of the motor, with the rest going to the motor output, how much angular speed is required to run this motor when 0.382 Nm torque is applied.

Reference no: EM13888156

Questions Cloud

Magnitude of average external torque : During the launch ,what is the magnitude of average external torque on her fromthe board?
Rotational inertia of the shell about that axis : A thin spherica lshel'I has a radius of 1.90 m. An applied torque of 960 N.m gives the shell an angular acceleration of 6.20 rad/s2 about an axis through the center of the shell. What is rotational inertia of the shell about that axis?
What is the difference between azotemia and uremia : What is the difference between azotemia and uremia - why is left ventricular dysfunction a concern for his physician?
What was your sales forecast strategy for your products? : What was your sales forecast strategy for your products?
Forms of internal energy of the motor : If one third of this energy goes into heat and other forms of internal energy of the motor, with the rest going to the motor output, how much angular speed is required to run this motor when 0.382 Nm torque is applied.
Prepare an administrative expense budget for duncan company : Duncan Company combines its operating expenses for budget purposes in a selling and administrative expense budget. Prepare a selling and administrative expense budget by quarters for the first 6 months of 2014.
Linkedin site to help you find a new job : 1.You graduated from college four years ago and now have an information technology (IT) job.
Describe the pathophysiology of the influenza virus : Why did Marshalls presentation lead Patricia to think he had influenza and not a cold? Why is it important to medically evaluate and diagnose a potential influenza infection and
Prepare the manufacturing overhead budget for the year : Atlanta Company is preparing its manufacturing overhead budget for 2014. Prepare the manufacturing overhead budget for the year, showing quarterly data.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the reduction in the exit temperature of the

the compression stages in the axial compressor of the industrial gas turbine are close coupled making intercooling very

  A particle travels along the circular path x2 y2 r2 if

a particle travels along the circular path x2 y2 r2. if the y component of the particles velocity is vy 2r cos 2t

  Determining the energy and money the regenerator

In a dairy plant, milk at 4°C is pasteurized continuously at 72°C at a rate of 12 L/s for 24 h a day and 365 days a year. The milk is heated to the pasteurizing temperature by hot water heated in a natural-gas-fired boiler that has an efficiency o..

  How does this compare to the tabulated value of 5164 ft3lbm

assuming that steam can be treated as an ideal gas what would the specific volume of steam be at 600deg f and 120 psia

  Determine the radius of curvature of the particle path

A particle which movies in a two-dimensional curvilinear motion has coordinates in millimetres which vary with time t in seconds according to x=5t2 +4 and y=2t3 + 6. For time t =3s, determine the radius of curvature of the particle path and the magni..

  What is the required mass flow of the extraction steam

A regenerative steam power cycle has a closed feed water heater that heats 20 kg/s of water from 100°C, 20 MPa to 250°C, 20 MPa. The extraction steam from the turbine enters the heater at 4 MPa, 275°C, and leaves as saturated liquid.  What is the req..

  This system is now heated at constant pressure until the

five kilograms of saturated vapor water at 1 mpa is contained in a cylinder fitted with a movable piston. this system

  Determine specific enthalpy and velocity at exit of valve

Steam flows at steady state through a well-insulated pressure-reducing valve. At the inlet, the pressure is 4 MPa, the temperature is 320°C, and the velocity is 60 m/s. The pressure of the steam at the exit is 700 kPa.

  The particle a is mounted on a light rod pivoted at o and

the particle a is mounted on a light rod pivoted at o and therefore is constrained to move in a circular arc of radius

  Determine a the time required for the train to travel the

a commuter train traveling at 40 mi h is 3 mi from a station. the train then decelerates so that its speed is 20 mi h

  In an accelerator protons emerge with velocity of 25 x 108

in an accelerator protons emerge with velocity of 2.5 x 108 ms. the accelerator is 0.8km long.a if the acceleration is

  Compute the modulus of elasticity of the metal

During a test of a metal bar, it was found that a axial tensile force of 10,000 lbs resulted in an elongation of 0.023 in. The bar had these original dimensions, length 10 in. diameter 0.750 in. Compute the modulus of elasticity of the metal. What ki..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd