For laboratory application assignment

Assignment Help Electrical Engineering
Reference no: EM13731750

For Laboratory Application Assignment on pgs. 166-167 examine Fig. 5-38.
Perform calculations for:
I1 (current through R1)
I2 (current through R2)
I3 (current through R3)
It (total current delivered by voltage source)
Req (equivalent resistance)
V1 (voltage across R1)
V2 (voltage across R2)
V3 (voltage across R3)
P1 (power dissipated in R1)
P2 (power dissipated in R2)
P3 (power dissipated in R3)
Pt (total power dissipated by the parallel circuit)
Scan all calculations showing all work in a file called "Lab5_Analysis_StudentID".
Simulation:
Construct the parallel circuit in Fig. 5-38 with MultiSIM.
Measure the values:
I1 (current through R1)
I2 (current through R2)
I3 (current through R3)
It (total current delivered by voltage source)
Req (equivalent resistance)
V1 (voltage across R1)
V2 (voltage across R2)
V3 (voltage across R3)
P1 (power dissipated in R1)
P2 (power dissipated in R2)
P3 (power dissipated in R3)
Pt (total power dissipated by the parallel circuit)
Capture a screenshot of measured values and paste into a Word document entitled "Lab5_Simulation_StudentID"
Answer all questions in the "Parallel Circuit Characteristics" section on pgs. 166-167 in this same document. 

Reference no: EM13731750

Questions Cloud

What risks or challenges might a manager encounter : How will accomplishing these objectives support your success in management? What risks or challenges might a manager encounter if they have not mastered these objectives? Explain
Explain quality is in the eye of beholder : You need to do a weekend "project" to de-clutter your closet over the Thanksgiving. Use 5S tools to plan your "lean" activities. Quality is in the eye of beholder. Explain. Further, discuss how "doing right at first time" is related to the 4 costs ..
What is role of world bank in promoting international trade : How International Monetary Funds helps its member countries in their economic development and what is the role of World Bank in promoting International Trade? What are the functions of IDA and IRDB?
What is the types of switches and latch and momentary : What is the Types of Switches and Latch and Momentary operation switches ? I need a full report with pictures
For laboratory application assignment : For Laboratory Application Assignment on pgs. 166-167 examine Fig. 5-38.Perform calculations for:I1 (current through R1)I2 (current through R2)I3 (current through R3)
Identify and explian any considerations you will need : Identify any considerations you will need to employ to build and maintain the brand and customer loyalty
Derive the state diagram : Design a Moore machine to detect the sequence 00010a. Derive the state diagram.b. Derive the state table and flip-flop excitation equations.c. Draw the sequential circuit.
Explian summarizes background and what makes you unique : Summarizes your background and what makes you unique in a 1-paragraph elevator pitch, Identifies 3 to 4 companies you want to work for, and an explanation as to why
Find the carrier frequency : An AM signal has the equation v(t) =[15+4 sin (44 x 10^3t] sin (46.5 x 10^6t)Va. Find the carrier frequency.b. Find the frequency of the modulating signal.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate developed torque at a full load armature current

A 600 V, dc shunt motor has armature and field resistance of 15 ohms and 600 ohms respectively. When the motor runs unloaded, the ine current is 3 A, and the speed is 1000rpm. Calculate the developed torque at a full load armature current of 50 A.

  Write each step of the calculation to get maximum marks

Find Equivalent resistance Rt of given circuit and also find total current flowing in circuit .Draw the circuit diagram of each step otherwise you will lose your marks. Write each step of the calculation to get maximum marks and also mention theun..

  Calculate the maximum diameter of the cylinder tank

The strength of longitudinal joint in Fig. 1-17 is 33 kips/ft, whereas for the girth is 16 kips/ft. Calculate the maximum diameter of the cylinder tank if the internal pressure is 150 psi.

  Determine the s-n improvement due to the pre-emphasis

An FM receiver is modulated with a signal having a baseband bandwidth of 15 kHz and the maximum frequency deviation is 45 kHz. Assume that preemphasis is added with a 3-dB boost frequency of 5 kHz.

  Write function called balloon that will accept single value

Write a function called Balloon that will accept a single variable named S. The function should replace S with the square of S and repeat this process until S is either greater than 10^15 or less than 10^-15.

  A certain primary cell has a terminal voltage of 124

a certain primary cell has a terminal voltage of 1.24 volts when supplying a current of 2a. immediately after the

  What is approximate time taken by the car to reach electrode

A charge of 4 micro-Coulomb is applied to the surface of the car. If the car travels a distance of 2 meter between the two electrodes, and if the mass of the car is 200 grams, then what is the approximate time taken by the car to reach the second ..

  Find the magnitude of the voltage at the sending end

Assume the factory described in the previous problem is fed from a line having an impedance of 0.02 + j0.16-ohm. The voltage at the factory is maintained at 480 V(rms). Find the average power loss in the line before and after the load is added.

  Find the real power p and reactive power q for each motor

Given three induction motors, find the real power P, the reactive power Q, and the apparent power S for each motor. Alsofind P, Q, and S for the total motor load. Motor 1: draws an electrical power of 100kw with power factor=.90 lagging.

  Calculate the frequency response of the system at 25 hz

The transfer function of a discrete time system is given by H H(z) = z/(z-0.5) The system has a sampling rate of 100 Hz. Calculate the frequency response of the system at 25 Hz input frequency as a complex number in both rectangular and polar f..

  What is the error when the arm position is at 15 degree

The controlled variable in a closed-loop system is the direction of a robot arm. Initially, it is at 40o; then it is commanded to go to 22o. What is the error when the arm position is at 15o

  What is the total 3-phase original loadin watts and vars

A balanced, 3-phase, 3-wire, 60Hz, wye-connected source isserving a combination of balanced loads in various configurations.Measurement of the source line voltage indicates 480 voltsline-to-line. Measurement of the source line current indicates 23..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd