User Account

All Pages

For a vertical cylinder with an electric heater 2500watt at

Assignment Help Mechanical Engineering
Reference no: EM13345603

For a vertical cylinder with an electric heater 2500watt at the base,an inlet(lower part of cylinder with cold water at 25C) and outlet(upper part of cylinder, with hot water @ 100C) flow channel, how do  calculate the rate of change of heat with the cylinder, and the vertical temperature distribution along the cylinder's wall 

Reference no: EM13345603

Questions Cloud

A 14 ml solution of succinic acid has a concentration of 10 : a 14 ml solution of succinic acid has a concentration of 10 mm. this solution is titrated with 8 mm lithium hydroxide.
1 what is the molarity of a kfaq solution containing 116g : 1 what is the molarity of a kfaq solution containing 116g of kf in 1.00 l of solution?2 what is the molarity of an
Calculate the concentration of nitrate ions in the : you need to make a solution of cano32 for a class demonstration. first you measure a quantity of the solid cano32 by
Which of the following is a typical property of an ionic : which of the following is a typical property of an ionic compound?a a low melting pointb poor conductor of electric
For a vertical cylinder with an electric heater 2500watt at : for a vertical cylinder with an electric heater 2500watt at the basean inletlower part of cylinder with cold water at
Consider a coil which has a resistance of 0314omega and : consider a coil which has a resistance of 0.314omega and an inductance of 0.002 h being supplied by 240 vrms 50 hz ac
To obtain ksp for pbi2 we must calculate pb2 in each : from the experimental data we obtain i- directly. to obtain ksp for pbi2 we must calculate pb2 in each equilibrium
Calculate the molar concentration of oh - ions in an 137 m : calculate the molar concentration of oh - ions in an 1.37 m solution of hypobromite ion bro- kb 4.0
A 350 g sample of solid mgoh2 was treated with 500 ml of : a 3.50 g sample of solid mgoh2 was treated with 50.0 ml of 0.500 m h2so4aq. after the reaction was over some of the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The 2 mg car increases its speed uniformly from rest to 25

the 2 mg car increases its speed uniformly from rest to 25 ms in 30s up the inclined road. determine the maximum power

  Determine the temperature and the mass of the vapor in

piston cylinder device contains 0.06 m3 of saturated water vapor at 350 KPa pressure. Determine the temperature and the mass of the vapor in.

  Steady state thermal analysis

Steady State Thermal analysis can be use to simulate and obtain results to support the design optimization / objectives

  Determine the rate of heat loss from the steam pipe

Taking the temperature of the surrounding surfaces to be 20°C also, determine the rate of heat loss from the steam pipe.

  How does tension spread over the line abad

A small boat hangs from two davits, one of which is shown in the figure. The tension in line ABAD is 82 lb, determine the moment about C of the resultant force exerted on the Davit.

  Determine line efficiency

When these stops occur, it takes an average of 10.0 min to diagnose the problem and make repairs. Determine (a) line efficiency and (b) average actual production rate.

  Find alpha the angular acceleration

Note that the positive y direction is downward and counterclockwise torques are positive. find alpha the angular acceleration?

  Determine the pressure and the internal energy

refrigerant -134a at 800kPa and 25 C is throttled to a temperature of -20C. determine the pressure and the internal energy of the refrigerant at the final state.

  Compare with the efficiency of an otto cycle

Also, compare with the efficiency of an Otto cycle operating with the same maximum pressure.

  Derive equations for shear and moment

Design a wide flange, simply supported beam below so that the stress due to bending does not exceed that allowed by AISC for A36 steel and calculate the shear stress where the parts join as indicated. Maximum V = 10,000 lb.

  Find the axial stress in individual component

The system shown below is deflected in compression by 6 = 0.014 in. For individual components 1, 2 & 3 find the axial stress in individual component

  Determine the mass fractions of alpha and beta phases

Determine the mass fractions of alpha and beta phases, Determine the mass fractions of primary beta and eutectic microconstituents, Determine the mass fraction of eutectic beta

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd