Find what is the fluid velocity ft per day in the aquifer

Assignment Help Civil Engineering
Reference no: EM13299310

Two monitoring wells were constructed in an unconfined aquifer. The wells are separated by a distance of 250 ft. The water surface elevations in the up-gradient and down-gradient wells were 101.00 and 100.85 ft, respectively. The aquifer hydraulic conductivity is 5 ft/day. What is the fluid velocity (ft/day) in the aquifer?

Reference no: EM13299310

Questions Cloud

At what maximum speed can the sports car negotiate the curve : A sport utility vehicle (SUV) and a sports car travel around the same horizontal curve. The SUV has a static stability factor of 0.74, At what maximum speed can the sports car negotiate the curve without rolling over
Determine the bod concentration leaving each pond : The volume of the first pond is 5.0 million gallons, and the second pond is 3.0 million gallons. Assuming complete mixing within each pond, find the BOD concentration leaving each pond
Explain sample of khc8h4o4 is dissolved n water : The acidic anion reacts with strong bases according to the following net ionic equation HC8H4O4-(aq) + OH- (aq)--->C8H4O4-2(aq) + H2O(l) If a 0.902g sample of KHC8H4O4 is dissolved n water and titrated to the equivalence point
What is the initial angular velocity of the disk : A small block having mass m sits on a uniform disk that has radius R=0.5m. What is the initial angular velocity of the disk
Find what is the fluid velocity ft per day in the aquifer : Two monitoring wells were constructed in an unconfined aquifer. The wells are separated by a distance of 250 ft. The water surface elevations in the up-gradient and down-gradient wells were 101.00 and 100.85 ft, respectively.
What is the firm cost of goods sold : Ellicott City Manufacturers, Inc. has sales of $6,344,210, and a gross profit margin of 67.3 percent. What is the firm's cost of goods sold?
Define an aluminum soft-drink can in an aqueous base : Dissolve an aluminum soft-drink can in an aqueous base. 2 Al (s) + 2 KOH (aq) + 6H20 (l)---> 2KAI(OH)4(aq) + 3H(g) If you place 2.05g of aluminum in a beaker with 185 mL of 1.35 M KOH, will any aluminum remain. What mass of KAI(OH)4 is produced
How corporations are taxed on dividend income : Which of the following best describes how corporations are taxed on dividend income?
Determine what is the expected efficiency of the system : A disinfection process for potable water treatment is described by first order kinetics with a rate constant of 0.08 minute. An ideal plug flow reactor is used with a hydraulic residence time of 1 hour. What is the expected efficiency of the syste..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determining the dry volume

A saturated sample of clay with an sl 20 has a natural water content of 32%. What would its dry volume be as a percentage of its original volume of Gs.= 2.67.

  Design a horizontal curve with a 40-degree central angle

Design a horizontal curve with a 40-degree central angle (delta=40) for a two-lane road with 11-ft lanes. The design speed is 70 mi/h and superelevation is limited to 0.06ft/ft. Give radius, degree of curvature, and length of curve.

  Estimate the wet density

A sample of natural glacial till was taken from below the groundwater table. The water content was found to be 52%. Estimate the wet density,dry density,buoyant density,porosity,and void ratio. Clearly state any necessary assumptions.

  Pharmaceutical mixing tank

In year one, a pharmaceutical mixing tank had a market price of $120,000. It replaced an older smaller mixing tank that had a BV of $15,000.

  Cylindrical pressure vessel with hemispherical ends

A cylindrical pressure vessel with hemispherical ends has a 2.5-m radius and a 5-mm wall thickness. It contains a gas with pressure pi = 6×10 5 Pa and the outer wall is subjected to atmospheric pressure p 0 = 1 × 10 5 Pa.

  Explain roman technology and engineering

Roman technology and engineering. Technology and engineering were among Rome's most famous achievements. Describe and explain the importance of Roman technology and engineering

  What is the maximum column load in kips that could be placed

What is the maximum column load in kips that could be placed on a 4-ft square temporary footing on a sand for which the standard resistance is about N=15 and the water table is at the surface A factor of safety of 2 is to be maintained against bea..

  Formulate and solve the minimum weight design

consider the cantilever beam-mass system. formulate and solve the minimum weight design.

  Regenerative thermal oxidizers

A company that manufactures regenerative thermal oxidizers made an investment 10 years ago that is now worth $1,300,000.

  What is the design speed of he curve

An equal-tangent crest vertical curve is designed with a PVI at station 110+00 and a PVC at station 107+43.3. if the high point is station 110+75.5 what is the design speed of he curve?

  Determine what is the outlet air temperature

A total of 13,610 kg/h of air at 1 atm abs pressure and 15.6C is to be heated by passing over a bank of tubes in which steam at 100C is condensing. The tubes are 12.7mm OD, 0.61 m long, and arranged in-line in a square pattern with Sp=Sn= 19.05mm.

  Maximum deflection of the beam

Determine the deflection of the right end of the pointer and the maximum deflection of the beam.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd