Find what is its cut-off frequency of a low pass filter

Assignment Help Electrical Engineering
Reference no: EM13256553

1. For a first order low pass filter, with a cut-off of 2 kHz, how many decades and octaves would the frequency be if the attenuation was -58 dB? What would the frequency be at that attenuation?

2. If the filter in the first problem was a first order high pass filter, with the same cut-off frequency, what would the two answers be?

3. If you had a second order low pass filter, and at 100 kHz the attenuation was -64 dB, what is its cut-off frequency?

Reference no: EM13256553

Questions Cloud

Focus on other 3 perspective not the financial perspective. : The strategy the company, is it: to increase profit through eliminating the perverse incentive or no focus on the profit as the question asking to focus on other 3 perspective not the financial perspective.
Prepare bank reconciliation statement : Prepare Bank Reconciliation Statement as on 30th September
What would the fatal voltage : A human can be electrocuted if a current of 0.053 A passes near the heart. If a human is considered to be a resistor in a circuit with a resistance of 2039 ?,
Explain what is the resulting ph : If 3.7 g of butanoic acid, C4H8O2, is dissolved in enough water to make 1.0 L of solution, what is the resulting pH
Find what is its cut-off frequency of a low pass filter : For a first order low pass filter, with a cut-off of 2 kHz, how many decades and octaves would the frequency be if the attenuation was -58 dB. What would the frequency be at that attenuation.
What is the receivables turnover : Dome Metals has credit sales of $468,000 yearly with credit terms of net 60 days, which is also the average collection period. Dome does not offer a discount for early payment, so its customers take the full 60 days to pay.
Find the rotational inertia of wheel : A wheel consists of 20 thin spokes, each with mass 0.070kg , attached to a rim of mass 4.4kg and radius 0.85m. Find its rotational inertia
What pressure of co would need to use to prepare a solution : If you wanted to prepare a solution of CO in water at 25 in which the CO concentration was 2.1 mM , what pressure of CO would you need to use
Calculate two variances for material-labor : The following information concerns the Dormnat Company, which manafactures one product and uses astandard cost system.

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  What is the signal-to-noise ratio of the spread signal

Suppose that a voice signal normally occupies 30 kHz of bandwidth and has a signal-to-noise ratio of 20 dB. Spread-spectrum techniques are used to increase its bandwidth to 2 MHz. (a) What is the signal-to-noise ratio of the spread signal

  Determine the compensator pole of utility feedback system

A unity feedback control systems for a robot submarine has a plant with a third-order transfer function G(s) = K / (s(s + 10)(s +50)) We want the overshoot to be approximately 7.5% for a step input

  How to add a third tone to the modulating signal

Experiment by changing the amplitudes of the modulating tones, and by adding a third tone to the modulating signal. First establish what you expect , then confirm by computer simulation.

  Design a 4-bit counter f using d-flip flop

The counter will use the falling edge of the clock (denoted by Clk) and have a separte reset pin (R) which will reset the counnter to 0000 when it is low (e.g. R=0). Please use D type flip-flops. write down the state diagram , and state table.

  Find the reflection coefficient at the load

A 75- ohm lossless transmission line is interfaced to a load impedance that consists of a series connected resistor of 30 ohm and a capacitor of 10 pF. At an operating frequency of 2 GHz and for a wavelength of 10 cm.

  Build a home security system circuit using program

Build a home security system circuit using this program. The system must include 2 door sensors, 3 window sensors, 2 smoke detectors, 2 water leak sensors, and 2 motion detectors.

  Find the frequency response of the system

For the system represented by the following difference equation y[n] = 0.5x[n] + 0.5x[n - 1] find: (a) the transfer function H(z) of the system. (b) the frequency response H(e^jw) of the system.

  Write declaration for function named validateeyecolor

A function must be defined or declared above the locations in the source code file from where it is called. We declare a function by writing a function declaration (which is a statement so it ends with a semicolon).

  Design the current divider so that the resistors are less

Design a current divider that will provide a 1/3-2/3 current splitting ratio. Use resistance in kilo ohm range. Redesign the current divider so that the resistors are less than 100 ohms but maintain the same 1/3-2/3 splitting ratio.

  What is the probability that team c is not successful

A conservative design team C and an innovative design team I are asked to separately design a new product within a month. From past experience, we know  The probability that team I is successful is 1/2  The probability that one and exactly one team..

  Find valve of starting resistor limiting armature current

A 500V shunt dc motor has a nominal armature current of 40A, and operates at 1200 rpm. if the armature resistance is 0.25 (ohm), calculate The valve of a starting resistor limiting the initial armature current to 60A

  Whether an fet is operating in ohmic region or active region

Discuss the operation of a JFET, including the pinch off and gate-source cutoff voltage in your explanation. Discuss how you can tell whether an FET is operating in the ohmic region or the active region.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd