Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Consider a VBE multiplier with R1=R2= 1.2k ohms utilizing a transistor that has VBE= 0.6V at Ic = 1ma, and a very high beta. (b) Find the value of the current I that will result in the terminal voltage changing (from the terminal voltage 1.2-v value) by 50mv, 100mv, 200mv, -50mv, -100mv, -200mv.
You are lowering two boxes, one on top of the other, down the ramp shown in the figure by pulling on a rope parallel to the surface of the ramp. Both boxes move together at a constant speed of 16cm/s.
For each one of the 3 frequency responses, H(f), in parts (a), (b), and (c) do the following: i. Obtain the system's impulse response, h(t). ii. Indicate if the system is BIBO stable or not, and state why. iii. Indicate if the system is causal or not..
A load consists of a resistance R in parallel with a capacitor of reactance X. The load is fed from a single phase supply through a line of impedance 8.4 + j11.2 ohms. The rms voltage at the load terminal is 1200 at 0 degress V rms,
A sinusoidal message signal has a frequency of 10 Hz. The signal is the input to an FM modulator with an index of 8. Determine the bandwidth of the modulator output if a power ratio, Pr = 0.8 is required.
An n-channel MOS device in a technology for which oxide thickness is 20nm, minimum channel length is 1μm, k'n = 100μA/V2, and Vt=0.8 V operates in the triode region, with small vDS and with the gate-source voltage in the range 0V to +5V.
A transmission line with no loss, with Z0= 60 ohms, is operated at 60MHz. The velocity on the line is c. The line is soldered to a ground connection at z=0. Find the input impedance into this line at z= -1.25 meters
Determine the peak-to-peak current ripple in the output inductor for a forward converter and determine the output voltage ripple of the converter . We know the following parameters: duty cycle d, input voltage Vin, turn ratio: N1/N2
The plant contains six 288MW generators. Given the overall facility efficiency is 76%, and the plant is capable of full output for a duration of 5 hours, determine the potential energy of upper reservoir and the minimum amount of water in gallons ..
In the movement of a robot arm, the arm is commanded to go from position 1 to position 5. Discuss the rise time, the overshoot, the settling time, and the steady-state error as it applies to the movement of a robot arm
Design a circuit that will multiply the input voltage by +12. That is the output voltage is 12v1 where v1 is the input voltage. All resistors should be at least 12ohms.
You balanced a pump impeller by placing a 5 gram weight at a radius of 100 mm. The original vibration amplitude was 10 mm/s, and after adding the balancing weight, the vibration is 1 mm/s. The speed of the pump is 1500 rpm and the weight of the im..
Seawater with a specific weight of 64.0 lbs/ft^3 is at a level of 4 feet above the centerline of the exit pipe. The tank is closed at the top and there is a pressure of 1 psig above the seawater. What is the velocity at the end of the pipe
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd