Find the wnet-efficiency-back work ratio-rate of heat input

Assignment Help Mechanical Engineering

Reference no: EM13706655

An Ideal reheats Rankine cycle. From 1 to 2 we go through Turbine 1. Then 2 to 3 we reheat in a steam generator. Then 3 to 4 we go through Turbine 2. Then from 4 to 5 we go through a Condenser. From 5 to 6 we go through a pump. Then we go through a super heater and it adds heat at a constant pressure back to 1. We have P1=9 MPa. P2 = 0.7 MPa. P4 = 0.009 MPa T1 = 520 C T3= 460 C and State 2 is a Saturated vapor. Find the Wnet(rate of work), Efficiency, BWR(back work ratio), and Qh(rate of heat input).

Reference no: EM13706655

Questions Cloud

Calculate the conduction heat loss for the following wall : Calculate the conduction heat loss for the following wall: 15ft long, 8ft tall. Calculate for 8 hr, inside temperature at 78F and the outside temperature at 3F. Wall components from outside to inside are brick; 1.2cm(1/2 in.) plywood; wood studs, 5x1..

Height difference between two columns of mercury manometer : A vertical frictionless piston-cylinder device contains nitrogen at 125 kPa. The outside atmospheric pressure is 100kPa. The piston diameter is 25 cm. The height difference between the two columns of mercury manometer (in cm), connected to the side o..

Find the final volume and the mass of air : An air pistol contains compressed air in a small cylinder, shown in Fig. P5.134. Assume that the volume is 1 cm3, pressure is 1 MPa, and the temperature is 27°C when armed. A bullet, m = 15 g, acts as a piston initially held by a pin (trigger); when ..

Determine the total deformation of the specimen : The specimen shown has been cut from a 1/4 in.-thick sheet of vinyl ( E = 0.45 X 106 psi) and is subjected to a 350-lb tensile load. Determine ( a) the total deformation of the specimen, (h) the deformation of its central portion BC.

Find the wnet-efficiency-back work ratio-rate of heat input : An Ideal reheats Rankine cycle. From 1 to 2 we go through Turbine 1. Then 2 to 3 we reheat in a steam generator. Then 3 to 4 we go through Turbine 2. Then from 4 to 5 we go through a Condenser. From 5 to 6 we go through a pump.

Contains a two-phase liquid-vapor mixture of refrigerant : A Closed, Rigid tank contains a two-phase liquid-vapor mixture of Refrigerant 22 initially at -20oC with a quality of 50.36%. Energy Transfer by heat into the tank occurs until the refrigerant is at a final pressure of 6 bars. Determine the final tem..

What is the rate of heat loss per meter of pipe : A pipe with OD 6.03cm, ID 4.93cm carries steam at 250deg C with h = 200 W/m^2.K The pipe is covered with 2.5cm of magnesia (85%) insulation followed by 2.5cm of polystyrene (k = .025 W/m.K The outer surface is exposed to air at T = 20 deg C with h = ..

Angular velocity and angular acceleration of the slotted arm : If a slider block C is fixed to the disk that has a constant counter clockwise angular velocity of 4 rad/sec, determine the angular velocity and angular acceleration of the slotted arm AB at the instant shown.

Pressure and specific volume in isentropic compression : Starting from the ideal gas law and the first law of thermodynamics derive the relationship between a) pressure temperature and, b) pressure and specific volume in isentropic compression show detail proof.

User Account

All Pages