Find the voltages vr and vc using the voltage divider rule

Assignment Help Electrical Engineering
Reference no: EM13262401

for the circuit where Vr=30 Ohms, L=20 mH, C=39uF, and e=squareroot of 2(20)sin(1000t+40 degrees)

a. Determine I, Vr, and Vc in phasor form

b. Calculate the total power factor and indicate whether it is leading or lagging

c. Calculate the average power delivered to the circuit

d. Draw the impedence diagram

e. draw the phasor diagram of the voltages E, Vr, Vc, and the current I

f. Find the voltages Vr and Vc using the voltage divider rule and compare them with the results from (a)

g. Draw the equivalent serices circuit of the above as far as the total impedance and current i are concerned.

Reference no: EM13262401

Questions Cloud

Design an two or three stage amplifier : Design an two or three stage amplifier that :Operates from single supply of no more than +10 V, and consumes no more than 10 mA. Has an RIn = 50 Ohms w/in 10%. Has an ROut less than or equal to 1kOhms.
Calculate the stocks expected return and standard deviation : Calculate the stock's expected return and standard deviation
Compute the mass of sodium azide : Calculate the mass (in grams) of sodium azide required to generate enough nitrogen gas to fill a 57.0-L air bag at 1.37 atm and 25.0 degree C
Discuss three reasons for adding international securities : Identify and briefly discuss three reasons for adding international securities to the pension portfolio and three problems associated with such an approach.
Find the voltages vr and vc using the voltage divider rule : for the circuit where Vr=30 Ohms, L=20 mH, C=39uF, and e=squareroot of 2(20)sin(1000t+40 degrees) a. Determine I, Vr, and Vc in phasor form b. Calculate the total power factor and indicate whether it is leading or lagging
Under what conditions would expect a real gas compressible : Under what conditions would you expect a real gas to be (a) more compressible than an ideal gas; (b) less compressible than an ideal gas
Develop the relation between semimajor axis and inclination : Mars has an orbital period of 1.881 Earth years, Develop the relation between semimajor axis and inclination for a Mars circular sun-synchronous orbit
Ind the minimum sampling rate without causing aliasing : Determine for each of following 4 signals if it is bandlimited and, if yes, find the minimum sampling rate without causing aliasing. (a) x1(t) = cos(500pt) + sin(700pt); (b) x2(t) = sin2(50pt);
How fast is the ship traveling : As measured in Earth's frame of reference, two planets are 485,000 km apart. How fast is the ship traveling

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Define j-k flip flop circuit design

This solution shows how to work from a given circuit implementation (a J-K flip flop circuit design) to derive the Boolean Logic and in so doing so simplify such logic using Boolean Algebra rules

  Calculate the hole density after aluminum acceptor atoms

4H-SiC is doped with 2 x 1017 cm-3 nitrogen donor atoms (Ec - Ed = 90meV). Use Nc = 4 x 1020 cm-3. a. Calculate the electron density at 300 K. b. Calculate the hole density at 300K after adding 2 x 1018 cm-3 aluminum acceptor atoms

  Calculate the magnetizing current and core losses

A transformer on no load takes 4.5 A at a power factor of 0.25 lagging when connected to a 120V, 60Hz supply, the number of turns of the primary winding is 250. Calculate the magnetizing current, core losses and the maximum value of flux in the co..

  Construct a canonical sum of products-sop expression

A farmer owns two barns; one north of a creek and the other south of the creek. The farmer has a Cabbage, a Goat, and a Wolf. The Farmer needs to put each item in a barn every night. If the Cabbage and Goat are in the same barn

  What is the total number of photons that will be emitted

If there are 500 atoms in the sample and assuming that from any state all possible downward transitions are equally probably, what is the total number of photons that will be emitted when all atoms return to the ground state

  Explain what bit pattern

What bit pattern (after you remove the beginning and ending flags and any stuffed bits) will the receiver pass on for higher level processing?

  Explain the significance of these intersections

construct a vertical line on your I versus V graph at the point V=5V. this line will intersect each of the sloping lines at two separate points. explain the significance of these intersections.

  Find input current and power factor at maximum torque

A 500 hp, three-phase, 2200 V, 60 HZ, 12-pole, Y-connected, wound-rotor induction motor has the following parameters: R1 = .225 ohm : R'2= .235 ohm Xeq = 1.43 ohm and Xm = 31.8 ohm and Rm = 780 ohm

  Find the depletion width nd its extent in each of the region

The acceptor concentration in a particular junction is 10^6/cm^3 and the donor concentration is 10^15/cm^3. Assume ni=1.5*10^10/cm^3. Find the junction built-in voltage.

  Evaluate laplace transforms

Analyse and Model Engineering Situations and Solve Engineering Problems using Laplace Transform

  How many atoms are there per cubic unit cell

A 3-D cubic unit cell contains four atoms whose centers are positional halfway up along each of the vertical cell edges and one atom each centered in the middle of the top and bottom faces.

  Calculate theoretical range when measuring resistance

how to calculate theoretical range when measuring resistance with DMM (amprobe-AM530) how to adjust the tektronics TBS1104 oscilloscope Time/div to a value of 0.5ms the tektronics only let me adjust between o and 1 ms, but nothing in between.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd